Fluke LinkRunner - LinkRunner Configuration and Settings; Ping Configuration; Manual IP Address Entry; LinkRunner Device Settings

Ping / LinkRunner Configuration
Press both action buttons simultane-
ously to access configuration (Ping
or LinkRunner
). If no
cable is connected, press
to
access Configuration.
Ping Configuration
• Press
to configure IP
addresses for pinging.
• Press
to highlight an
item.
• - press
for
DHCP on/off.
Note: manual IP address configuration changes will be
ignored until you turn off DHCP.
User-defined IP Addresses
- press
to enter user-defined IP addresses
(up to 4 common IP address ping targets).
• Press to cycle through ping targets 0 - 4. Tar-
get 0 means you don’t want to ping a target.
• Press
to access IP edit-
ing then press
to begin
editing the selected target.
Entering an IP Address
• Press
to increment
each digit.
• Press
to advance.
• Press to exit.
Note: Invalid addresses revert to the previous value
(class D, E, 0.0.0.0, or 255.255.255.255).
• - press to access IP
Configuration.
• Press to highlight an
address:
LinkRunner IP address
Subnet Mask
Default Router
Manual IP
Configuration
• Press the right selection button
to begin editing an address.
• Press to then .
LinkRunner
Configuration
• From the Ping/LinkRunner
Configuration screen, press
LinkRunner Configura-
tion.
• Displayed are the LinkRunner
MAC address and version.
• Press to select feet or
meters.
• Press to exit.
Other Features and Functions
Unpowered
Device
Token Ring
Telco
No DHCP
Server found
Auto-off: unit powers off after 5 minutes of inactivity
(auto-off disabled during ping or cable locate tasks).
Restore Factory Defaults: press power button as you
press both selection buttons.
Ping Responder: In ping mode LinkRunner responds
to pings from other devices.
Duplicate IP
addresses found
Help Technical Assistance Center
Have a question about using LinkRunner? Contact the
Technical Assistance Center at one of the numbers
listed or e-mail: support@flukenetworks.com.
USA
1-800-283-5853 Japan +81-3-3434-0181
Canada
1-800-363-5853 China +86-10-6512-3435
Europe
+31-402-675-200 Singapore +65-6-738-5655
Anywhere +1-425-446-4519
You can also visit the Fluke Networks Knowledge Base
at http://kb.flukenetworks.com.
Accessories
Buy LinkRunner accessories or other network test
products by contacting a Fluke Networks representa-
tive or send e-mail to: sales@flukenetworks.com. For
more information go to
www.flukenetworks.com/linkrunner.
Accessories Part No.
Cable ID Kit (IDs 1-8) 1665935
Clip Set 1668377
Toner Receiver 1667985
Wiremap Adapter (ID #0) 1668404
Rechargeable Batteries 1572184
Battery Charger 1572191
RJ-45 Coupler 1668361
Cleaning Clean unit with a damp cloth.
h
Caution If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the equipment may be impaired.
Warranty
LinkRunner carries a one-year warranty. Find
out more at
www.flukenetworks.com/linkrunner.
Specifications
P
European directive
Meets EN61010-1 1
st
and 2
nd
editions.
Meets EN61326 Class A, for ESD criteria C, FCC part 15
Class A.
$ Canadian Nationally Recognized Test Laboratory for U.S.
and Canada
Meets CSA/CAN C22.2 No.1010.1-92, UL3111-1.
j Not intended to be connected to telecommunication line.
;
N10140
Meets C-Tick EMC standard.
?