Fault Finding Chart
WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT CHECK ACTION
Is the automatic line feed
working?
Manually feed out line.
SEE “MANUAL LINE FEED”
Is the line fed out and visible?
Has line been removed from
cleat?
Remove cap and spool, free line
and re-fit spool and cap. SEE
“CUTTING HEAD”
The line may be jammed on the
spool. Rewind line to remove
crossed loops. Check that line is in
correct section of spool.
Is the manual line feed working?
Has too much line been fed out? SEE “MANUAL LINE FEED”
Contact your local approved
Service Centre or Husqvarna UK
Ltd. Customer Service.
Is the line cutter missing from the
safety guard?
Contact Husqvarna UK Ltd. Customer Service
Telephone : 0844 844 4558 UK 1800 882 350 ROI
No
No
No
Yes
Yes
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS
CLATTERING NOISE
LINE SNAPS
CONTINUOUSLY
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
Has the motor reached full speed
before use?
No
Allow the motor to reach full speed
before use.
Are you using the trimmer
correctly?
?
Only use tip of nylon line to trim.
SEE “How to trim and edge”
Is the line jamming on the spool?
Yes
Rewind the line on the spool, if
symptoms still persist, change
spool and line.
Clean wheel and groove on trimmer head. SEE “MAINTENANCE”
WHEEL STOPS TURNING
Replacement Parts
Spool and Line
Reference no.: FLY021 Part no.: 513937190
If any part is found to be defective due to faulty manufac-
ture within the guarantee period, Husqvarna UK Ltd.,
through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge pro-
viding:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and
tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not au-
thorised by Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way dimin-
ishes the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accor-
dance with the instructions and recommendations
contained in this Operator's Manual.
* Machines used for hire are not covered by this guaran-
tee.
* The following items listed are considered as wearing
parts and their life is dependent on regular mainte-
nance and are, therefore not normally subject to a
valid warranty claim: Nylon Line, Spool and Line, Elec-
tric Mains Cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly
or indirectly by the fitting of replacement parts or addi-
tional parts that are not either manufactured or ap-
proved by Husqvarna UK Ltd., or by the machine
having been modified in any way.
Guarantee & Guarantee Policy
Service Recommendations
• Your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a professional
application.
To Next Page
Loading...
Need help?
General