此功能用于当接收机无法正常收到发射机的信号不受控制时，保护模型和操作人员的安全。
接收机 CH2 通道默认开启失控保护，失控后电调进入刹车模式；而 CH1 通道、CH3 通道 和 CH4 通道，可在发
射机端设置相应的失控保护值。默认未设置，未设置时 PWM 接口保持最后输出。
功能设置：
发射机开机正常通信状态下，将需要设置的通道保持在需要设定的失控保护值位置保持不动，同时长按对码键
(BIND）3 秒，G.LED 指示灯闪烁 2 秒表示设置成功，即当接收机无法接收信号后，将按照设定的失控值输出。
此初学者模式比较适合入门级玩家，通过对油门幅度的控制来提高操作的安全性。
初学者模式模式油门输出仅为 50% ，即 CH2 通道范围默认为 1250~1500~1750us。出厂默认为正常模式。
功能设置：
切换初学者模式和正常模式：按住 CH4 按键，同时将方向手轮逆时针打到底，并开机，当 G.LED 指示灯二闪一
灭持续3 秒时，表明切换到初学者模式；正常模式时，G.LED 指示灯灭。
支持四轮转向模式设置，用于设置控制车辆转向的车轮，适用于前后轮均带转向功能的部分攀爬车类型。
四轮转向模式复用 CH4 通道，由 CH4 按键控制。要设置四轮转向控制方式，需先切换到四轮转向模式。
驱动控制模式 / 四轮转向模式切换
发射机正常开机状态下，同时短按 BIND 按键和 CH4 按键，即可切换驱动控制模式和四轮转向模式，默认驱动
控制模式。
注：模式切换后，关机保存设置。
切换到四轮转向模式后，可顺序设置五种转向控制方式：仅前轮转向、前后反向、前后同向、仅后轮转向（正向
）和仅后轮转向（反向）。
功能设置：长按 CH4 按键（≥ 2 秒 ) 切换模式。每长按控件一次切换一种模式。默认前轮转向。
Beginner mode is designed for people new to the hobby.
In this mode the throttle channel has been limited to output 50 percent, the channel range defaults has
been set to 1250~1500~1750us. By default, the mode is normal mode.
Setup:
To switch between beginner mode and normal mode, press and hold the CH4 button while turning the
steering wheel completely counterclockwise as far as it can, and at the same time, power on the
transmitter. When the G.LED works in two-flash-one-off mode for 3 senconds, then the beginner mode
has switched. In case of the G.LED is off, the normal mode is switched.
The transmitter supports four-wheel steering function which is used to set the wheels that control the
steering of the vehicle. This function adapts partial crawler types with steering on both front and rear
wheels.
The four-wheel steering function is controlled by CH4 channel, and the control is CH4 button. Switch to
four-wheel steering function firstly, then set the control mode.
Switching the drive control/four-wheel steering function
In the normal power-on state, press both the BIND button and the CH4 button to switch between the
drive control and four-wheel steering. The drive control is the default mode.
Note:The setting will be save when the transmitter turns off.
After switching to four-wheel steering function, you can set the control mode in turn: Front wheel
steering, front and rear wheels reversal steering, front and rear wheels in the same steering, rear wheel
steering (normal) and rear wheel steering (reverse).
Setup:
Press and hold the CH4 button over 2 senconds to switch the mode. Switch one mode per press of the
control. By default, it is front wheel steering.
17
Beginner Mode
初学者模式
Four-wheel Steering
四轮转向
System Functions
系统功能
To Next Page
Loading...
