EasyManua.ls Logo

FOAMICO MO 0145-4 - User Manual

Default Icon
37 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1 MO 0145-4 NEXT 701613-18_UK 15-04-2019
Operation Manual
FOAMICO NEXT
Mobile station with Compressor
MO 0145-4 (7011613).
Mobil station without Compressor X-AIR
MO 0145-4 (7011618).

Table of Contents

Questions and Answers

  • V
    velazqueznathanielAug 6, 2025
    Why is the foam quality low on my FOAMICO Cleaning Equipment?
    • J
      Justin RushAug 6, 2025
      If you're experiencing low foam quality with your FOAMICO Cleaning Equipment, ensure that compressed air is supplied to the system by opening the air inlet. Verify you are using the correct foam product and that an original 50/200 foam nozzle with a white nozzle guard is installed. Confirm the system has sufficient air supply, requiring a minimum of 150 l/min and a maximum of 200 l/min at 4-6 bars. Adjust the air pressure to 4-6 bars using the air regulation valve and ensure the operation selector is set to the 'foam' position.
  • R
    Robert PerezAug 21, 2025
    How to fix no rinsing pressure in FOAMICO MO 0145-4?
    • T
      Taylor SharpAug 21, 2025
      If you're experiencing no rinsing pressure with your FOAMICO Cleaning Equipment, start by ensuring the mobile unit is running. Check that you aren't exceeding the maximum number of users at the same time. Also, verify that the ball valve at the system's inlet is fully opened.
  • J
    jose10Aug 28, 2025
    What causes unstable rinsing pressure in FOAMICO Cleaning Equipment?
    • J
      Jessica AdkinsAug 28, 2025
      If you're experiencing unstable rinsing pressure with your FOAMICO Cleaning Equipment, it might be due to using a non-original rinsing nozzle with excessive water consumption. Replace it with a master rinsing nozzle, making sure to observe the technical data for your specific model.
  • N
    Nancy JohnsonNov 13, 2025
    What to do if FOAMICO MO 0145-4 Cleaning Equipment does not suck up detergent?
    • A
      Anthony FloresNov 13, 2025
      If your FOAMICO Cleaning Equipment system isn't drawing detergent into the injector, first, ensure the operation handle is in the 'foam' position. Check if the limiting nozzles are appropriately sized and adjust the dosing according to the detergent supplier's description, changing the nozzle if necessary. Inspect the limiting nozzle and injector system for chemical remains, disassembling and cleaning them if blocked. Look for leakages on the detergent inlet, replace the suction hose if air is being drawn in. Also, check for a blocked suction filter at the end of the suction hose, cleaning or replacing it as needed. Ensure the chemical container is not empty and that the suction filter is submerged below the fluid level. Finally, confirm that compressed air is supplied to the system by ope...

Summary

Introduction

Condition of Liability

User responsibility for system treatment and operation.

Guarantee Conditions

Warranty terms for parts, excluding wear and frost damage.

Protection Against Frost

Importance of installing in frost-free rooms and emptying the system.

Safety

Safety During Operation of the System

Recommendations for working clothes, PPE, and safe system operation.

Precautionary Measures

Adherence to technical requirements and accident prevention stipulations.

Safekeeping

Storing the manual for easy access and handing over to responsible personnel.

Declaration of Conformity

Statement of product conformity with directives like Machinery.

Appropriate Utilization

Defines the intended uses: rinsing, foam spreading, and disinfection.

Models and Symbols

Symbols

Visual indicators for operation modes like Off, Rinsing, Foaming, and Disinfection.

Models

Lists different versions of the Mobil Unit available.

Model Overview

Visual representation of different model configurations.

Installation

Safety Instructions for Mounting and Installation

Crucial safety instructions for mounting and initial setup.

Location and Mounting

Guidelines for placing the system in a frost-free room and secure mounting.

Water Supply

Requirements and precautions for connecting the water supply.

Electrical Supply

Safety warnings and requirements for electrical connections.

Supply of Detergent and Sanitizer

Instructions for connecting detergent and sanitizer.

Operation

Start and Stop Procedure

Step-by-step guide for starting and stopping the mobile station.

Rinsing Operation

Procedure for performing rinsing tasks.

Foam Operation

Steps for applying foam using the system.

Spray Disinfection

Instructions for using the system for spray disinfection.

Stop of Operation

Final steps to safely shut down and secure the system.

Troubleshooting; Failures

Troubleshooting

Table of common faults, their causes, and recommended actions.

Failures Control System

Details on specific system failures and their resolution steps.

Maintenance

Rinsing hose

Daily checks and recommended replacement for the rinsing hose.

Nozzles

Regular checks and replacement advice for nozzles.

Low pressure valves; guns

Periodic checks and tightening of valves and guns.

Couplings

Cleaning and greasing guidelines for couplings.

Ball valves

Adjustment frequency for ball valves to prevent leakage.

Non-return valves

Importance and checks for non-return valves.

Suction filter; chemical hose

Cleaning and replacement schedule for filters and hoses.

Technical data

Spare parts

Enclosure Mobile unit MO 0145- 4. With and without compressor

Identification of enclosure parts for the mobile unit.

Overview Mobile unit MO 0145-4 with compressor

Exploded view and part numbers for the unit with compressor.

Overview Mobile unit MO 0-5 without compressor

Exploded view and part numbers for the unit without compressor.

Pipe system Rinse and foam block

Details on parts for the rinse and foam pipe system.

Spare parts Rinse and foam block. 1001040-44 - 1001218

Specific part numbers for the rinse and foam block assembly.

Spare parts Rinse and foam block. 1001309-13

Specific part numbers for another rinse and foam block assembly.

Spare parts foam and rinse block, positioning ring, injector

Part numbers for foam/rinse block, positioning ring, and injector configurations.

Spare parts foam; rinse block, positioning ring, injector. Without compressor

Part numbers for configurations without a compressor.

Spare parts: Air regulator complete with bracket 1001488

Part numbers for the air regulator and its bracket.

Electrical diagram

Spare parts Control box compressor 1001492

List of components and part numbers for the control box.

Flow diagram MS0145-0 - MS0145-5. With compressor

Diagram illustrating fluid paths for units with a compressor.

Flow diagram MO 0145-1 - 5 without compressor

Diagram illustrating fluid paths for units without a compressor.

Name plate

Declaration of Conformity

FOAMICO MO 0145-4 Specifications

General IconGeneral
BrandFOAMICO
ModelMO 0145-4
CategoryCleaning Equipment
LanguageEnglish