Fostex 4030 - Before Switch on Power; Method of Adjusting; Slave Servo Adjusting and Servo Characteristic Learning

85 pages

Save Page as PDF

To Next Page

To Previous Page

Main Page

Safety Instructions2
Table of Contents3
Controls4
Front Panel Facilities5
Lock Enable Button/Indicator5
Chase Enable Button5
Offset Modify Button5
Rear Panel Facilities6
Offset Retard Button6
Offset Clear Button6
Transport Control Connector6
Slave Section7
Servo Adjusting Section7
Damping Selector7
Tape Speed Indicator7
Synchronizer Controller8
Record Mode Indicator8
Lock Enable Indicator8
Master Time Code Indicator8
Slave Time Code Indicator9
Display Indicator9
Control Select Button/Indicator9
Lock Enable Button9
Record Mode Select Button10
Review Button10
Record Indicator10
Zone Limit Button/Indicator10
Data Entry Section11
Auto Return Button/Indicator11
Store Key/Indicator11
Period/Display Hold Key11
Lock Mode Select Buttons12
Offset Trim Button/Indicator12
Plus/Preroll Key12
Minus/Offset Key12
Frame Lock Button/Indicator13
Auto Lock Button/Indicator13
Sync Lock Button/Indicator13
Synchronizer Connector13
Connecting Examples with Various Equipments14
Sync System of Two Audio Decks14
Basic Audio Sweetening System15
System Setup When Using the Time Code Generator as a High Speed Reader16
Exmple of Code Only Master17
Example of Using a VTR for the Slave18
One Master Three Slave System19
Sync with a Film Transport Using the Bi-Phase Interface19
Preparation before Operating20
Setting the Rear Panel DIP Switches20
Servo Gain21
Servo Offset21
Before Switch on Power22
Method of Adjusting22
Slave Servo Adjusting and Servo Characteristic Learning22
Servo Output and Tape Speed23
2Nd Mode26
Memory Initialized Condition26
List of 2Nd Mode Functions27
Tape Speed Indication28
Setting of Locate Damping28
Relearning of Relationship between Tach Pulse and Time Code29
Setting of the "Direction Signal Disregarding" Mode29
Setting Mehod Using the 403529
Setting by the 4030 Only30
Setting Using the 403531
Display/Setting of the Frame Number33
Code Only Master34
Code Mode34
Play to Park Function35
Auto Rec with Offset36
Setting the Slave Park Point37
Setting the Damping Factor for the Lock Mode38
Damping Range38
Operation40
Transport Control Functions41
Basic Operation to Lockup Machines42
Edit Mode43
Editing/Storing of Time Data43
Editing/Storing of Zone or Auto Return Data45
Locate Function (Locate Button)46
Review Function (Review Button)47
Preroll Function47
Display Hold48
Offset Memory48
Changing the Preroll Time48
Confirming the Preroll Time48
Storing the Prevailing Reader Display Offset Value into Offset Memory49
Trim Offset Using the Offset Trim Button and the +/- Keys49
Auto Function50
Zone Limit50
Auto Play51
Auto Return51
Auto Recording51
Addition and Subtraction of Time Data52
Rehearsal Mode52
Take Mode52
Lock Mode54
Tach Pulse Learning in the 460 Mode54
Sync Lock54
Auto Lock54
Notes on Using the 1 Master 3 (or 2) Slave System55
Time Code at off Line Editing56
Technical Information57
Transport Interface57
Interconnections57
Equipment Which Can be Connected57
Reference Signal58
Control Signal59
Logic Input/Output60
Status of the Logic Input Signals60
Slave Speed Control, Pins 5, 11, 1262
Transport Control Interface Circuit64
Software Version 3.10 Manual65
Improvements over Existing Function66
Newly Added Functions68
Synchronizer/Controller72
Contents73
About Version 3.20 Software74
Machine Select76
Slave Start Point and Park Area76
Setting Values77
How to Find the Optimum Value77
Sofware Version Display80
Speed Display Mode80
Chase Window Width80
Punch out Mode80
Low Speed Area81
Slave Code Enable81
No Tach Pulse Mode82
Control Pulse Width82
External Sync Mode82
Parity Bit83
Number of Communication Data Bit83
Number of Stop Bit83
Locked Window83
Stop Tally Ignore84
Set up Conditions of Machine Select84
Second Mode Summary85

Fostex 4030 - Before Switch on Power; Method of Adjusting; Slave Servo Adjusting and Servo Characteristic Learning

Table of Contents

Related product manuals