Fox Micron - User Manual

To Next Page

ENGLISH

www.foxint.com

Features

Fitting the Batteries

BLUE LED

On / Off

Micro Light Slots

Battery Cover

Power Out Socket

(2.5mm)

Volume Control

Tone Control

Buzzer Bar Locking Screw

High Quality Cone Speaker

Rigid 3/8” Stainless Steel Thread

Extension Socket

(2.5mm)

D-Tec Sensing System™

(DTSS)

• Weatherproof Sealed Case

• Digital Circuitry

• See-Saw Effect Elimination Feature

• Audible & Visual Backdrop Indication

• Low Battery Drain

• CNC Machined Rollerwheel - Tru-Run™

1. Turn off unit prior to fitting or

replacing batteries.

3. Pull the lower tab up to remove

the battery cover.

5. For best weatherproofing, ensure

battery cover has a good seal by firmly

pushing the edging of the battery cover.

2. Using the supplied screwdriver

unscrew the two battery cover screws.

4. Take care removing the batteries.

Insert new batteries and ensure

correct polarity.

6. Re-fit cover and screws.

DO NOT over tighten the battery compartment screws,

excessive force will damage the screw threads.

Switching On / Off

Power Off

Power On

• Push down and release the power switch to activate the unit.

• Push up and release the power switch to deactivate the unit.

(LED will briefly flash red)

Please note:

The unit does not beep when

switched on or off.

Battery Requirements

The Microns require 2 x LR6 AA 1.5V Alkaline batteries. The use of good quality

batteries is essential for maximum battery life. To reduce the risk of battery leakage:

• DO NOT mix old and new batteries

• DO NOT mix different battery types

• The use of rechargeable batteries is NOT recommended

Buzzer Bar Locking Screw

This allows infinite alignment adjustability for the Micron facing position. If the Micron is

not facing the desired position, unscrew the micron until you can reach the locking screw.

Back the locking screw a quarter to half a turn, then screw the Micron back on.

Controls Additional Extras

Notes

Volume Control

Turn the knob clockwise to increase volume, anti-clockwise to lower volume.

There are eight different volume settings available.

Tone Control

Turn the knob clockwise to raise pitch, anti-clockwise to lower pitch.

There are eight different tone settings available.

Micron N Series Hardcase

Product Code: CEI102

Sockets

Extension Socket

Extension socket for wired extension boxes or remote system.

Power Out Socket

Allows Fox Illuminated Bite Indicators to be powered directly

from the Micron. The Illuminated Indicator will then light up

when the Micron is activated and latch for approximately

20 seconds.

When the Micron detects that its batteries are failing, the main LED colour

changes to purple. When this occurs, batteries should be replaced at the earliest

opportunity, although the unit may continue to work for some time in this

condition, particularly if the volume setting is reduced. No audible indication of

low battery is given. It is not possible to change the LED colour once it has

changed to purple.

Low Battery Warning

Warranty & Product Registration

Customer Reference Number and a Warranty Reference Number, please make

a note of these numbers. You can view warranty details online using the

Customer Reference number.

Alternatively ﬁll out the Warranty Card enclosed in the box and post to:

Customer Care Department

Fox International Group Ltd, UK Headquarters,

56-58 Fowler Road, Hainault Business Park,

Hainault, Essex, IG6 3UT

Micron is a Registered Trade Mark

NTX-R, NX, N & NTX Receiver are Registered Trade Marks

We reserve the right to alter or modify the contents of this manual.

NEVER place batteries in a hot environment (e.g. on a radiator).

Drying Out After Use in Heavy Rain

These Microns have been designed to be weatherproof. However, after use in

heavy rain, it is important to allow the unit to dry out properly by bringing the

unit indoors and removing the hard case cover.

Warnings

• Do not trigger LED or speaker in close proximity to human or animal eyes and ears.

• Store this equipment out of reach of children and infants.

• Avoid dropping or subjecting the Micron to severe impacts.

• Use only recommended batteries and accessories.

MICRON USER GUIDE

Need help?

Do you have a question about the Fox Micron and is the answer not in the manual?

Summary

Controls

Volume Control

Adjusts sound volume clockwise to increase, anti-clockwise to decrease. Offers eight settings.

Tone Control

Adjusts sound pitch clockwise to raise, anti-clockwise to lower. Offers eight settings.

Sockets

Extension Socket

Provides an extension for wired extension boxes or remote systems.

Power Out Socket

Powers illuminated bite indicators directly from the Micron for approximately 20 seconds.

Additional Extras

Micron N Series Hardcase

Protective case for the Micron unit, identified by product code CEI102.

Drying Out After Use in Heavy Rain

Warranty & Product Registration

Summary

Controls

Volume Control

Adjusts sound volume clockwise to increase, anti-clockwise to decrease. Offers eight settings.

Tone Control

Adjusts sound pitch clockwise to raise, anti-clockwise to lower. Offers eight settings.

Sockets

Extension Socket

Provides an extension for wired extension boxes or remote systems.

Power Out Socket

Powers illuminated bite indicators directly from the Micron for approximately 20 seconds.

Additional Extras

Micron N Series Hardcase

Protective case for the Micron unit, identified by product code CEI102.

Drying Out After Use in Heavy Rain

Warranty & Product Registration

The Fox Micron is a sophisticated digital bite alarm designed for anglers, featuring a weatherproof sealed case and advanced digital circuitry. Its primary function is to alert the user to a fish bite through both audible and visual indications, incorporating a "See-Saw Effect Elimination Feature" to prevent false alarms.

Technical Specifications:

Power: Requires 2 x LR6 AA 1.5V Alkaline batteries.
LED: Blue LED for visual indication.
Speaker: High-quality cone speaker for audible alerts.
Thread: Rigid 3/8" stainless steel thread for secure mounting.
Sensing System: D-Tec Sensing System™ (DTSS) for reliable bite detection.
Rollerwheel: CNC Machined Rollerwheel - Tru-Run™ for smooth operation.
Sockets:
- Extension Socket (2.5mm) for wired extension boxes or remote systems.
- Power Out Socket (2.5mm) to power Fox Illuminated Bite Indicators, which light up for approximately 20 seconds upon activation.
Battery Life: Features low battery drain.
Rating: 3Vm.

Usage Features:

Switching On/Off:

To activate the unit, push down and release the power switch. To deactivate, push up and release the power switch (the LED will briefly flash red). The unit does not beep when switched on or off.

Volume Control:

The Micron offers eight different volume settings. Turn the knob clockwise to increase volume and anti-clockwise to decrease it.

Tone Control:

There are eight different tone settings available. Turn the knob clockwise to raise the pitch and anti-clockwise to lower it.

Buzzer Bar Locking Screw:

This feature allows for infinite alignment adjustability of the Micron's facing position. If the Micron is not facing the desired position, unscrew it until you can access the locking screw. Back the locking screw a quarter to half a turn, then screw the Micron back on to adjust its angle.

Micro Light Slots:

These slots are integrated into the design, likely for attaching or illuminating micro lights, enhancing visibility in low-light conditions.

Battery Installation:

Turn off the unit before fitting or replacing batteries.
Using the supplied screwdriver, unscrew the two battery cover screws.
Pull the lower tab up to remove the battery cover.
Carefully remove the old batteries. Insert new LR6 AA 1.5V Alkaline batteries, ensuring correct polarity.
Re-fit the cover and screws, ensuring a good seal by firmly pushing the edging of the battery cover for best weatherproofing.
- Caution: Do not overtighten the battery compartment screws, as excessive force can damage the screw threads.

Battery Requirements & Warnings:

The Microns require 2 x LR6 AA 1.5V Alkaline batteries. Using good quality batteries is essential for maximum battery life. To reduce the risk of battery leakage:

DO NOT mix old and new batteries.
DO NOT mix different battery types.
The use of rechargeable batteries is NOT recommended.

Low Battery Warning:

When the Micron detects that its batteries are failing, the main LED colour changes to purple. Batteries should be replaced at the earliest opportunity. The unit may continue to work for some time in this condition, especially if the volume setting is reduced. No audible indication of low battery is given. It is not possible to change the LED colour once it has changed to purple.

General Warnings:

Do not trigger the LED or speaker in close proximity to human or animal eyes and ears.
Store this equipment out of reach of children and infants.
Avoid dropping or subjecting the Micron to severe impacts.
Use only recommended batteries and accessories.

Maintenance Features:

Drying Out After Use in Heavy Rain:

While Microns are designed to be weatherproof, it is important to allow the unit to dry out properly after use in heavy rain. This involves bringing the unit indoors and removing the hard case cover.

Caution: NEVER place batteries in a hot environment (e.g., on a radiator).

Product Registration:

Users can register their Fox product online at www.foxint.com. Upon registration, a Customer Reference Number and a Warranty Reference Number will be provided, which can be used to view warranty details online. Alternatively, a Warranty Card enclosed in the box can be filled out and posted to the Customer Care Department at Fox International Group Ltd, UK Headquarters.