Franke FDWS 614 D8P DOS E

Questions and Answers

J
Jessica LopezAug 13, 2025
Why won't my Franke Dishwasher start or respond to commands?
- K
  Kellie SmithAug 13, 2025
  Your Franke Dishwasher might not start or respond to commands due to several reasons: * It may not be plugged in properly, so ensure the plug is fully inserted into the socket. * A power outage may have occurred. Press the START/Pause button to resume the cycle. * The dishwasher door may not be fully closed. Push the door vigorously until you hear a 'click'. * If the door was opened for more than 4 seconds during a cycle, close it and press START/Pause. * If the display shows F9 or F12 and both On/Off and START/Pause LEDs are blinking rapidly, switch the appliance off and on again after one minute. If the issue continues, unplug the appliance for one minute, then plug it back in.
P
patrick89Aug 17, 2025
What to do if my Franke FDWS 614 D8P DOS E Dishwasher won’t drain and shows F3 error?
- L
  Luis RiveraAug 17, 2025
  If your Franke Dishwasher won’t drain and the display shows F3 with blinking LEDs, it could be due to several reasons: * The wash cycle may not have finished yet; wait until it completes. * The drain hose might be bent; check and straighten it. * The sink drain pipe could be blocked; clean it. * The filter may be clogged with food residues; clean the filter.
C
Cody PhillipsAug 21, 2025
What to do if my Franke FDWS 614 D8P DOS E finishes the cycle prematurely with F15 error?
- T
  Tammy BrownAug 21, 2025
  If your Franke Dishwasher is finishing cycles early and displaying error F15, the issue might be: * The drain hose positioned too low or siphoning into home sewage system. Check if end of drain hose is placed at correct height. Check for siphoning into home sewage system, install air admittance valve if necessary. * Air in water supply. Check water supply for leaks or other issues letting air inside.
L
Logan DavidsonAug 25, 2025
How to fix Franke FDWS 614 D8P DOS E when it does not fill the water and shows F6 error?
- C
  Crystal TranAug 25, 2025
  If your Franke Dishwasher isn't filling with water and shows F6 error, check these: * Ensure there is water in the water supply and the tap is open. * Make sure the inlet hose is not bent. * The sieve in the water inlet hose may be clogged; it is necessary to clean it. After cleaning, turn the dishwasher off and on, then restart a new program.
S
Sarah NelsonAug 28, 2025
Why is the salt indicator lit on my Franke FDWS 614 D8P DOS E Dishwasher?
- S
  sharonmorrisAug 28, 2025
  The salt indicator on your Franke Dishwasher may be lit because the salt reservoir is empty. Refill it with salt. Note that after refilling, the indicator may remain lit for several wash cycles. Also, ensure you adjust the water hardness settings appropriately.
Y
youngsherylAug 31, 2025
Why is the rinse aid indicator lit on my Franke FDWS 614 D8P DOS E?
- A
  Arthur GarciaAug 31, 2025
  The rinse aid indicator on your Franke Dishwasher is lit because the rinse aid dispenser is empty. Refill the dispenser with rinse aid. After refilling, the rinse aid indicator may remain lit for several wash cycles.
A
Anthony BaileySep 4, 2025
Why are my dishes not clean in my Franke Dishwasher?
- K
  kellypooleSep 4, 2025
  If your dishes aren't getting clean in your Franke Dishwasher, here are some potential causes: * The crockery may not be arranged properly. Arrange the crockery correctly. * The spray arms might be blocked by dishes. Arrange the crockery correctly to allow free rotation. * The selected wash cycle might be too gentle. Select an appropriate wash cycle. * Too much foam may have been produced due to incorrect detergent usage. Ensure the detergent is measured correctly and is suitable for dishwashers. * The rinse aid compartment cap may not be closed correctly. Make sure the cap is securely closed. * The filter might be dirty or clogged. Clean the filter assembly. * There might be no salt in the dishwasher. Fill the salt reservoir.
R
Rebecca MorganSep 8, 2025
Why is my Franke FDWS 614 D8P DOS E Dishwasher making excessive noise?
- L
  Laura MacdonaldSep 8, 2025
  Excessive noise from your Franke Dishwasher can be caused by: * Dishes rattling against each other. Position the crockery correctly. * Too much foam. The detergent has not been measured out correctly or it is not suitable for use in dishwashers. Restart dishwasher by pressing the DRAIN button and run new program without detergent.