Need help?Do you have a question about the Friedrich PZE12K3SB and is the answer not in the manual?
General| Brand | Friedrich |
|---|---|
| Model | PZE12K3SB |
| Category | Air Conditioner |
| Language | English |
Guide to understanding the model number structure of PTAC/PTHP units.
Guide to interpreting the serial number format for PTAC/PTHP units.
Detailed list of standard features and their benefits on Friedrich PTAC units.
Technical specifications for 7-9k BTU PTAC units with electric heat.
Technical specs for 7-9k BTU PTAC units with heat pump functionality.
Technical specs for 12-15k BTU PTAC units with electric heat.
Technical specs for 12-15k BTU PTAC units with heat pump functionality.
Details on voltage, amperage, receptacles, and fuse/circuit breaker types for PTAC units.
Instructions for wiring 265V PTAC/PTHP units, including conduit kit usage.
Explanation of buttons, display functions, error codes, and temperature parameters for unit operation.
Step-by-step explanation of the refrigeration cycle principles and operation in PTAC units.
Visual representation of refrigerant flow in cooling + heat pump and cooling + electric heat modes.
Instructions for cleaning and inspecting the unit's coils and chassis for optimal performance.
Guidelines for proper PTAC unit installation, including minimum clearance requirements.
Step-by-step instructions for installing the PDXWS wall sleeve for PTAC units.
Instructions for installing PTAC units in various wall types like panel, frame, block, and brick veneer.
Instructions for installing the optional PXDR10 drain kit for internal condensate drainage.
Instructions for connecting an external drain system for condensate removal.
Installation instructions for the PXGA standard grille, including mounting details.
Steps to prepare the unit chassis for installation, including removing protective components.
Procedures for physically installing the unit chassis into the wall sleeve.
Safety precautions and steps for connecting the unit's power supply or hard wire connector.
Checklist for ensuring all installation steps are complete and the unit is ready for operation.
Warning regarding EPA regulations for servicing refrigeration systems without proper certification.
Procedures and considerations for accurately charging R-410A refrigerant into the system.
Symptoms, causes, and checks for systems with insufficient refrigerant charge.
Symptoms, causes, and checks for systems with too much refrigerant.
Troubleshooting partial and complete restrictions in the refrigerant system.
Acceptable method for charging the sealed system using the weighed-in charge method.
Checking for restricted capillary tubes in units equipped with capillary tube metering devices.
Explanation of the 4-way reversing valve's function in controlling refrigerant flow direction.
Procedure for testing the continuity of the reversing valve solenoid coil.
Steps to check the reversing valve's operation by switching between heating and cooling modes.
Procedures for replacing the reversing valve, including brazing and safety precautions.
A chart for diagnosing reversing valve malfunctions based on tube temperatures.
Methods for checking compressor electrical and mechanical integrity, including L.R.V. and R.L.A. tests.
Procedures for replacing a compressor, including system preparation and leak testing.
Special steps for compressor replacement following a burnout, including system flushing.
Common malfunctions and their corresponding solutions for PTAC units.
Analysis of malfunctions like start failure, control panel issues, and fan problems.
Steps to diagnose and resolve issues related to the unit losing power.
Troubleshooting steps for a non-functional control panel on the PTAC unit.
Identifies errors E2, E3, E4, E5 related to temperature sensor malfunctions.
Troubleshooting steps for the E4 error, indicating potential indoor outlet overheating.
Troubleshooting for E8 error, indicating evaporator issues in cooling or overheat in heat pump mode.
Troubleshooting for E9 error, indicating refrigerant high pressure protection.
Steps to diagnose and resolve issues where the compressor fails to start or run.
Troubleshooting steps for when the electric heater function is not operating.
Wiring diagram for a 7K BTU Cool+ Electric Heat unit operating at 230V.
Wiring diagram for 9K BTU Cool+ Electric Heat units at 230V and 265V.
Wiring diagram for 12K BTU Cool+ Electric Heat units at 230V and 265V.
Wiring diagram for a 15K BTU Cool+ Electric Heat unit operating at 230V.
Wiring diagram for a 7K BTU Cool+ Heat Pump unit operating at 230V.
Wiring diagram for 9K BTU Cool+ Heat Pump units at 230V and 265V.
Wiring diagram for 12K BTU Cool+ Heat Pump units at 230V and 265V.
Wiring diagram for a 15K BTU Cool+ Heat Pump unit operating at 230V.
Introduction to the illustrated parts catalog, explaining its structure and usage.
Exploded view illustration of parts for PZE series PTAC units.
Exploded view illustration of parts for PZH series PTAC units.
Description of accessories for new construction installations, like sleeves and grilles.
Details on the Lateral Duct Adapter for directing airflow to a second room.
Conversion tables for Fahrenheit and Celsius temperatures and ambient temperature ranges.
Table showing resistance values for thermistors at various temperatures.
Details of the limited warranty for the first 12 months of PTAC/PTHP unit installation.
List of authorized parts depots for Friedrich equipment.
To Next Page