Frymaster FPEL Series

Questions and Answers

J
Jessica WebsterAug 7, 2025
What to do if my Frymaster FPEL Fryer displays 'SERVICE REQUIRED – ATO BOARD'?
- C
  Catherine VasquezAug 7, 2025
  If your Frymaster Fryer's controller displays 'SERVICE REQUIRED – ATO BOARD', first, check the fuse on the right side of the ATO box to ensure it is secure and in good condition. Also, if the controller above the ATO box lacks power, inspect the fuse below the component box. Next, with the controller turned OFF, press the TEMP button to see if the ATO software version appears. If it doesn't, the connection between the ATO and the controller might be faulty. Ensure the 6-pin CAN connectors are tightly secured between the controller (J6 and J7) and the ATO (J9 or J10) boards. Finally, check that there is correct voltage to the ATO transformer. Restore power to the board and clear any service required errors.
L
littlemichaelAug 11, 2025
What to do if my Frymaster FPEL Fryer controller displays 'TOPOFF OIL EMPTY / CONFIRM'?
- C
  Chris ConnerAug 11, 2025
  If the controller on your Frymaster Fryer displays 'TOPOFF OIL EMPTY / CONFIRM', simply fill the top off system with oil and then press the ? (CONFIRM) button.
B
burchjudithAug 15, 2025
Why is one vat not topping off in my Frymaster Fryer?
- W
  William FrazierAug 15, 2025
  If one vat on your Frymaster Fryer is not topping off, a filter error may exist. Ensure you properly clear any filter errors. Alternatively, there might be an issue with the ATO pump, loose wire connections, the RTD, or the ATO board itself. Check the ATO pump, wire connections, RTD and ATO board.
J
Jeanne MaxwellAug 20, 2025
What to do if one vat tops off but other vats fail to top off on my Frymaster FPEL Fryer?
- J
  Jessica JordanAug 20, 2025
  If one vat of your Frymaster Fryer tops off, but the others don't, the solenoid on the vats that are not topping off may have failed. Check the power to the pump. If the pump is hot, the solenoid has probably failed. Also, make sure all wiring harnesses are securely connected to the ATO board and solenoids.
C
chelsea34Aug 25, 2025
Why is my Frymaster FPEL topping off the incorrect vat?
- D
  Douglas CollinsAug 25, 2025
  If your Frymaster Fryer is topping off the incorrect vat, first, ensure that all the wires are correctly wired. Then, check if the flexlines are connected to the wrong vat and switch them to the correct vat if necessary.
K
Karen MirandaAug 28, 2025
How to troubleshoot no power to ATO board on Frymaster FPEL Fryer?
- D
  David Mitchell MDAug 28, 2025
  If there is no power to the ATO board of your Frymaster Fryer, check to ensure J5 on the front of the ATO board is fully locked into the connector. Also, verify that the fuse below the right control box and the fuse on the right side of the ATO box are not blown. Finally, check that proper voltage is present at the transformer.
A
alexandercarrilloDec 3, 2025
Why won't the frypots top off in my Frymaster Fryer?

Frymaster FPEL Series Specifications

General

Fryer Type	Electric
Series	FPEL
Controls	Digital
Construction	Stainless Steel
Power	Varies by model
Tank Capacity	Varies by model
Oil Capacity	Varies by model
Dimensions	Varies by model
Weight	Varies by model
Category	Fryer