Fujitsu ESPRIMO D957 - Reinstalling a Slot Cover

83 pages

To Next Page

To Previous Page

System expansio ns

Reinstalling a slot cover

► Push the slot cover into the slot (1).

► Tighten the screw (2, optional).

Fujitsu 63

Main Page

Table of Contents7
Your ESPRIMO11
Validity of the Reference Manual11
Notational Conventions12
Ports and Operating Elements13
Front13
Rear14
Important Notes15
Safety Information15
Transporting the Device15
Cleaning the Device16
Energy Saving, Disposal and Recycling16
Getting Started17
Unpacking and Checking the Delivery17
Steps for Initial Setup17
Setting up the Device18
Vertical Operating Position with Feet (Optional)18
Connecting the Device to the Mains Supply20
Connecting External Devices21
Ports on the Device21
Connecting a Monitor22
Connecting the Mouse22
Connecting the Keyboard23
Connecting External Devices to the Serial Interface23
Connecting External Devices to the USB Ports24
Switching on for the First Time: Installing the Software24
Switch on the Monitor and the Machine25
Installing the Software25
Operation26
Switch the Device on26
Switching off the Device26
Procedure in an Emergency26
Indicators on the Device27
Keyboard28
Important Keys and Keyboard Shortcuts28
Settings in BIOS Setup29
Property and Data Protection30
Mechanically Protecting and Locking the Casing30
BIOS Setup Security Functions31
Access Authorisation Via Smartcard31
Operating the Smartcard Reader (Optional)31
Problem Solutions and Tips32
Help if Problems Occur32
Troubleshooting32
Power-On Indicator Remains Unlit after You Have Switched on Your Device32
The Device Cannot be Switched off with the ON/OFF Switch33
Monitor Remains Blank33
No Mouse Pointer Displayed on the Screen34
Time And/Or Date Is Not Correct34
Smartcard Reader Is Not Recognised34
Smartcard PIN Forgotten35
Error Messages on the Screen35
Installing New Software35
Restoring the Hard Disk Contents35
Tips35
System Expansions36
Information about Boards37
Removing the Casing Cover38
Reattaching the Casing Cover39
Overview of Drive Bays and Drives in Your Device40
Changing the Drive Cover41
Installing and Removing an Accessible Slimline Drive in the Upper Bay (Optional)44
Installing the Drive Plate for the Slimline Drive44
Installing a Slimline Drive46
Removing a Slimline Drive47
Opening and Closing the Drive Cage49
Opening the Drive Cage49
Closing the Drive Cage50
Installing and Removing 2½ Inch Drives in a 3½ Inch Adapter51
Installing 2½ Inch Drives in a 3½ Inch Adapter51
Removing 2½ Inch Drives from a 3½ Inch Adapter53
Installing and Removing Drives in the Lower Bay (Optional)54
Installing and Removing a 3½ Inch Drive or a 3½ Inch Adapter54
Installing and Removing a 2½ Inch Drive (Screw Fastened)57
Installing and Removing Drives in the Middle Bay (Optional)59
Installing a 3½ Inch Drive59
Removing a 3½ Inch Drive61
Installing and Removing an M.2 Module62
Installing an M.2 Module62
Removing an M.2 Module63
Installing and Removing Low-Profile Boards64
Opening the Board Retaining Mechanism64
Removing a Slot Cover65
Installing a Board66
Removing Boards66
Reinstalling a Slot Cover67
Closing the Board Retaining Mechanism68
Installing and Removing WLAN Antennas69
Installing WLAN Antennas69
Removing WLAN Antennas70
Installing a Serial Port71
Installing and Removing Heat Sinks74
Removing the Heat Sink74
Installing the Heat Sink76
Mainboard Expansions77
Upgrading Main Memory77
Processor, Replacing77
Replacing the Lithium Battery78
Technical Specification79

Fujitsu ESPRIMO D957 - Reinstalling a Slot Cover

Table of Contents

Related product manuals