Fujitsu FUTRO X913 User Manual (English)

Other manuals for Fujitsu FUTRO X913

Questions and Answers:

B
Brenda BarrAug 17, 2025
How to fix a Fujitsu FUTRO X913 Desktop when the power indicator is off?
- M
  Miranda BakerAug 17, 2025
  If the power-on indicator on your Fujitsu Desktop remains unlit after switching it on, it could be due to a faulty mains voltage supply. Ensure the power cable is properly plugged into both the device and the mains socket. Alternatively, the internal power supply might be overloaded. In this case, unplug the device from the mains socket, wait approximately 3 minutes, then plug it back in and switch the device on.
Q
qmorganAug 19, 2025
What to do if my Fujitsu FUTRO X913 Desktop monitor remains blank?
- J
  Johnny ShepherdAug 19, 2025
  If your Fujitsu Desktop monitor remains blank, first check if power saving mode is activated. Press any key on the keyboard, deactivate the screen saver, or adjust the brightness and contrast. If that doesn't work, ensure the brightness control isn't set too low. If the issue persists, restart the device, press F8 during boot, start in protected mode, and set the correct value for the connected monitor as described in its operating instructions. Also, check the ambient temperature, as a darker screen can indicate inadequate heat dissipation, especially in passively cooled systems like the FUTRO X913/X913-T. If a 'Frequency out of range' message appears, adjust the video frequency range or screen resolution using your computer software.
S
Sean BestAug 22, 2025
Why is my external monitor blank on my Fujitsu FUTRO X913?
- J
  jacksonandrewAug 22, 2025
  If the external monitor connected to your Fujitsu Desktop remains blank, first ensure that the monitor is switched on and that its brightness is properly adjusted. If power saving mode is active, pressing any key should restore the display. If the screen output is set to the system’s LCD monitor, use the appropriate key combination to switch the screen output. Also, verify that the power and data cables are securely connected to both the system and the monitor. If connections are loose, switch off the external monitor and the system, check and properly connect the cables, and then switch them back on.
T
Theresa WilsonAug 25, 2025
Why is my Fujitsu Desktop's external monitor blank or unstable?
- B
  Bernard MillerAug 26, 2025
  If the external monitor connected to your Fujitsu Desktop is blank or the image is unstable, it might be due to an incorrect monitor selection or screen resolution setting within the application program. Terminate the program by pressing Alt + F4. If the issue continues, switch to the system's LCD monitor using the appropriate key combination and adjust the screen resolution as described in your operating system's documentation.
Z
zlewisAug 27, 2025
What to do if my Fujitsu Desktop won't switch off?
- N
  Nicole SampsonAug 27, 2025
  If your Fujitsu Desktop cannot be switched off using the ON/OFF switch due to a system crash, keep the power button pressed for at least 4 seconds. Be aware that this can lead to data loss, as it doesn't allow the operating system to shut down properly, and error messages may appear upon the next system start.
N
Nicole HernandezAug 30, 2025
How to restore mouse pointer on Fujitsu FUTRO X913 Desktop?
- L
  Lynn AndersonAug 31, 2025
  If no mouse pointer is displayed on the screen of your Fujitsu Desktop, ensure the mouse is correctly connected. Properly shut down the operating system, switch off the device, and check the mouse cable connections to the system unit, including any adapters or extension leads. Make sure only one mouse is connected before switching the device back on.
P
phillipszacharySep 2, 2025
How to correct the time on my Fujitsu FUTRO X913?
- E
  Eric MuellerSep 2, 2025
  If the time and/or date is not correct on your Fujitsu Desktop, set the correct time and date within the operating system or in the BIOS Setup.
M
Margaret PhamSep 5, 2025
What to do if Fujitsu FUTRO X913 Desktop doesn't recognize SmartCard?
- K
  kimberly92Sep 5, 2025
  If your Fujitsu Desktop's SmartCard reader does not recognize the card, ensure the SmartCard is inserted correctly with the chip facing upwards. Also, verify that the SmartCard complies with the ISO standard 7816-1, -2, -3, and -4.
T
Thomas CannonSep 8, 2025
What to do if I forgot my Fujitsu FUTRO X913 Desktop SmartCard PIN?
- D
  david93Sep 8, 2025
  If you have forgotten the PIN for your SmartCard on your Fujitsu Desktop and are working in a network, contact your system administrator. They can unlock your system using a Supervisor PIN.
C
Cassandra RobbinsSep 10, 2025
What to do if I lost my Fujitsu FUTRO X913 SmartCard?
- T
  Thomas FreemanSep 12, 2025
  If you have lost your SmartCard for your Fujitsu Desktop and are working in a network, contact your system administrator, who can boot your system with a Supervisor SmartCard.

Fujitsu FUTRO X913 Specifications

General

RAM	Up to 16GB DDR3
Storage	mSATA SSD
Graphics	Intel HD Graphics
Audio	Realtek ALC269, High Definition Audio
Operating System	Windows 10 IoT Enterprise
Connectivity	Gigabit Ethernet
Ports Front	2 x USB 2.0
Ports Rear	2x USB 3.0, 2x USB 2.0, 1x DisplayPort
Ports	1 x DVI-I, 1 x DisplayPort, 1 x RJ-45