Fujitsu PRIMERGY RX300 S7 - Page 9

System configurator and order-information guide
B
PRIMERGY RX300 S7 Status 2013-12-30
PRIMECENTER Rack
S26361-F2735-E145 S26361-F2735-E175 S26361-F2735-E111 Further information for
RMK-F1_DI_CMA_QRL
Rack Mount Kit F1-C S7 LV
No Rackmount-Kit option
rack mounting is available
best choice for PrimeCenter racks best choice for 3rd party racks
Only for loose deliveries within the
consisting of consisting of
No mounting in racks possible Corporate Partner Portal
vario carrier 714-785mm
vario carrier 559-914mm
max. 1x per system
telescopic drop-in rails 781mm telescopic drop-in rails 781mm All "L" no's for loose delivery
with quick release lever support with quick release lever support
with full extraction with full extraction S26361-F2735-L10
with CMA adapter with CMA adapter Adapter angle PC/DC-Rack, till 50Kg
1x per system
1x per system
C necessary for mounting RMKs in
asymmetrical PC racks
S26361-F2735-L145
RMK-F1_DI_CMA_QRL
S26361-F4530-E11
S26361-F4530-E10
best choice for PrimeCenter racks
Mounting 1U or 2U server in Mounting server in
with CMA adapter
asymmetrical racks symmetrical racks
with 1U support bracket no support bracket needed S26361-F2735-L175
RMK-F1_DI_CMA_QRL_LV
best choice for 3rd party racks
S26361-F2735-E71
S26361-F2735-E82
with CMA adapter
Lateral cable management Rack Cable Management Arm CMA 2U
for 2U servers or higher for 2U Server in racks
S26361-F2735-L176
- for asymmetrical racks
- for symmetrical racks
RMK-F1_DI_QRL_LV
PRIMECENTER S2 or M1
M1 or 3rd party racks
best choice for 3rd party racks
- 1 bracket PC Rack asym.
Fujitsu racks
w/o CMA adapter
1x per system 1x per system
S26361-F2735-L7
Lateral cable management (optionally)
can only be mounted
SNP:SY-F1647E301-P in asymmetrical PRIMECENTER
Installation ex works for one
S2 or new M1 racks in 1U above RMK
server or subsystem.
Hereby the rack will be delivered
S26361-F2735-L82
completely pre-mounted and
Rack Cable Management Arm CMA 2U
all wired connections are tested.
for 2U Server in racks.
With PCR M1 16U, 24U, 42U:
Systems and components S26361-F2201-L20
will be delivered installed in the rack
Cable arm 2U PCR M1 S and 3rd p.-racks
"Rack-mounting ex factory"
for L176, has to be mounted above RMK
This service is to be ordered once
per installable server/storage
subsystem, in order to get the
To be ordered only together with server/storage subsystem
a PRIMECENTER rack mounted into the racks.
PCR S2 e.g. S26361-K826-V10x In case of not-installed server and subsystems
new PCR M1 e.g. S26361-K827-Vxxx
this service has to be ordered,
refer PCR S2 or M1 rack configurator to get the mounting kits and the
max. 1x per System cables installed.
PRIMERGY Classic 19" rack is not supported
C
Fujitsu PRIMERGY Server 9 of 31