Why are serial ports not recognized properly in Device Manager on my Fujitsu Server?
This issue may arise if the Serial 1 and Serial 2 settings have been altered. To resolve this, remove all serial ports listed in Device Manager and then restart your Fujitsu Server.
What to do if nothing is displayed on the screen of my Fujitsu Primergy RX300 S2?
If your Fujitsu Server displays nothing on the screen, check the following: * Ensure the display cable is properly connected. * Verify that the brightness and contrast settings on the display are correctly adjusted. * Note that the issue may be related to an error in the system memory area.
What to do if keyboard controller error appears on Fujitsu Primergy RX300 S2?
If you encounter a keyboard controller error on your Fujitsu Server, the keyboard may be faulty. Try replacing the keyboard or mouse. If the error persists after replacement, the baseboard likely needs to be replaced.
What does 'Critical memory error occurred - system halted' mean on Fujitsu Primergy RX300 S2?
If your Fujitsu Server displays a 'Critical memory error occurred - system halted' message, it indicates a memory issue. First, restart the server. If the message reappears, consult the error log and replace the defective memory module.
How to resolve LAN Operation Fails on Fujitsu Server?
If LAN operation fails or an error message appears during LAN driver installation on your Fujitsu Server, it may be due to a conflict between system resources, including the LAN and other expansion cards. Try deleting all LAN drivers and ensure there are no conflicts between system resources.
Why is the screen shaking on my Fujitsu Server display?
If the screen on your Fujitsu Server display is shaking, it might be due to interference from a strong magnetic field. Devices like televisions or speakers placed near the display can cause this. Move such devices further away from the display, and avoid using cell phones near the display.
What does 'Memory type mixing detected' mean on Fujitsu Primergy RX300 S2?
If your Fujitsu Server shows a 'Memory type mixing detected' message, it means the memory installation configuration is incorrect. Ensure that the same type of memory is installed in the slots of the same bank.
How to fix distorted screen display on Fujitsu Primergy RX300 S2 Server?
If the screen display on your Fujitsu Server is distorted, especially during 3D program execution (or if the 3D program terminates abnormally), set the Color quality in screen properties to something other than True Color (32 bits).
What to do if Fujitsu Primergy RX300 S2 Server POST stops with 'Expansion ROM not initialized' message?
To resolve the "Expansion ROM not initialized..." message during POST on your Fujitsu Server, change [Reset Configuration Data] to [Yes] in the BIOS Setup Utility, found under "8.2.5 Advanced Menu".
What to do if Fujitsu Primergy RX300 S2 Server cannot collect the memory dump?
If your Fujitsu Server cannot collect the memory dump, check the settings of the paging file and memory dump file.
Introduces component names, basic operations, and software overview.
Covers server preparation and cautions for OS installation.
Details OS installation using ServerStart.
Explains manual OS installation.
Covers post-OS installation operations.
Recommends and explains high reliability tools.
Details installing internal options.
Explains environment settings for server operation.
Covers operations, daily care, and maintenance.
Details the process of creating necessary driver installation disks.
Explains step-by-step procedures for manual OS installation.
Introduces ServerView for monitoring server hardware status.
Introduces DSNAP for collecting failure investigation information.
Guides on installing a CPU, including socket locations and procedures.
Guides on installing memory modules, including slot locations and order.
Explains how to install expansion cards into PCI slots.
Guides on installing internal hard disk units into storage bays.
Guides on installing internal backup devices into storage bays.
Guides on installing an extension parallel port option.
General| Processor Sockets | 2 |
|---|---|
| Chipset | Intel 5000P |
| Network | 2 x Gigabit Ethernet |
| Form Factor | 2U Rackmount |
| Processor | Intel Xeon 5000/5100/5300 series |
| Storage | SAS or SATA HDD 2.5"/3.5" |
| RAID Support | Optional RAID controller |
| Operating System Support | Windows Server, Linux |
| Power Supply | Redundant power supply optional |
To Next Page
