4-1 FL13.8_DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
2. Disassembly Method
*1: all TYPE A models except for
LF320FX4F(Serial No.: ME1)
*2: LF320FX4F(Serial No.: ME1) and all TYPE B
models
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the
Tabl e."
Important precautions concerning the
LCD Panel Assembly:
1. When you disassemble/re-assemble the Stand
Holder for 32ME303V/F7 (Serial No.: ME2),
LF320EM4 (Serial No.: ME3), and LF320EM4F
(Serial No.: ME2) models.
• The CBA which is connected to the Digital Main
CBA Unit with CL3006 cannot be replaced alone.
This CBA can only be supplied as LCD Panel
Assembly. Be careful not to touch this CBA
unnecessarily.
2. When you disassemble/re-assemble the Front
Cabinet or Function CBA Unit
• Be careful not to break the hooks. If you pull with too
much force, the hooks may be damaged.
• Be careful not to scratch the display panel when
assembling.
• Be careful not to scratch the rear frame when
disassembling/re-assembling or when tightening the
screws.
• Make sure the Shield Plate is placed properly.
• The Function CBA Unit and Sensor Lens are fixed in
place by the hooks. Make sure these hooks are not
damaged. Make sure the Function CBA Unit and
Sensor Lens are securely in place when
re-assembling.
Step/
Loc.
No.
Part
Fig.
No.
Removal Note
[1] Rear Cover D1 7(S-1), 5(S-2) ---
[2]
Stand
Assembly
D1 3(S-3) ---
[3] Speaker
D2
D5
CN3801 ---
[4]
Stand
Holder
D2 4(S-4) 1
[5]
Power
Supply
CBA
D3
D5
4(S-5), CN501,
CN601, CN1001
---
[6]
Digital Main
CBA Unit
D3
D5
4(S-6), CN3013
*1
,
CN3006
*2
, CN3101,
Jack Holder
---
[7]
LCD Panel
Assembly
D4 ---------------- ---
[8]
Front
Cabinet
D4 8(S-7) 2
[9]
Function
CBA Unit
D4
Sensor Lens, Shield
Plate, Control Plate
2
↓
(1)
↓
(2)
↓
(3)
↓
(4)
↓
(5)
[1] Rear Cover
[2] Stand
Assembly
[5] Power Supply
CBA
[3] Speaker
[4] Stand Holder
[8] Front Cabinet
[6] Digital Main
CBA Unit
[7] LCD Panel
Assembly
[9] Function CBA
Unit
To Next Page
Loading...
