PL-PRO POWER CONDITIONER AND LIGHT MODULEPL-PRO POWER CONDITIONER AND LIGHT MODULE
3
Safety Information
To obtain best results from your Furman PL-PRO, please be sure to read this manual
carefully before using it.
WARNING: To reduce the risk of electrical shock, do not expose this
equipment to rain or moisture. Dangerous high voltages are present inside
the enclosure. Do not remove the covers. Other than the light bulbs, there are
no user serviceable parts inside. Refer servicing to qualified personnel only.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
Important Safety Instructions
Please read prior to installation
1. Please read and observe all of the safety and operating instructions before the
PL-PRO is operated. Retain these instructions for future reference.
2. The PL-PRO should not be used near water — for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, etc.
3. The PL-PRO should be situated so that its location and position do not interfere
with its proper ventilation. For example, the PL-PRO must not be placed on a rug,
bed, sofa, or similar surface which impedes airflow across the chassis.
4. Do not place the PL-PRO near heat sources such as radiators, heat registers,
stoves, or other appliances that produce heat.
5. The PL-PRO should only be connected to a 120
VAC, 60 Hz, 20 amp grounded electrical outlet.
Outlets wired for 20 amps may be identified by
the T-shaped socket opening that accepts the
perpendicular blades of the PL-PRO’s power plug.
If you don’t have a 20 amp outlet available, have
one installed by a qualified electrician. Do not
defeat the ground or polarization of the power plug.
6. Route the power cord and other cables so that they are not likely to be walked
on, tripped over, or stressed. Pay particular attention to condition of cords and
15 amp 20 amp
10
Three Year Limited Warranty
Important Note:
To be sure of obtaining full protection under the terms of the
Limited Warranty in case your ownership documents are lost, please fill out
and return the Warranty Registration Card immediately. Please verify that
the serial number shown on the Warranty Card matches the serial number
on your unit.
The Furman PL-PRO is warranted against failures due to defective parts or
faulty workmanship for a period of three years after delivery to the original owner.
During this period, Furman will make any necessary repairs without charge for
parts or labor. Shipping charges to the factory or repair station must be prepaid by
the owner; return shipping charges (via UPS Ground) will be paid by Furman.
This warranty applies only to the original owner and is not transferable. Also, it
does not apply to repairs done other than by the Furman factory or Authorized
Repair Stations.
This warranty shall be cancellable by Furman at its sole discretion if the
PL-PRO unit has been subjected to physical abuse, has been operated without a
proper safety ground, or has been modified in any way without written authorization
from Furman. Furman’s liability under this warranty is limited to repair or
replacement of the defective unit.
Furman will not be responsible for incidental or consequential damages
resulting from the use or misuse of its products. Some states do not allow the
exclusion of incidental or consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Warranty claims should be accompanied by a copy of the original purchase
invoice showing the purchase date (if a Warranty Registration Card was mailed in
at the time of purchase, this is not necessary). Before returning any equipment for
repair, please read the important information on service below.
Service
Before returning any equipment for repair, please be sure that it is adequately
packed and cushioned against damage in shipment, and that it is insured. We
suggest that you save the original packaging and use it to ship the product for
servicing. Also, please enclose a note giving your name, address, phone number
and a description of the problem.
NOTE: All equipment being returned for repair must have a Return
Authorization (RA) Number. To get an RA Number, please call the Furman Service
Department: (707) 763-1010, ext. 40. Please display your RA Number prominently
on the front of all packages.
To Next Page
Loading...
