Why is the antenna not rotating on my Furuno FAR-2318?
If the antenna is not rotating on your Furuno Marine Radar, it could be due to the antenna drive mechanism or the MTR-DRV board. Consider replacing the antenna drive mechanism or the MTR-DRV board.
Why can't I operate my Furuno Marine Radar from on-screen boxes?
If you cannot operate your Furuno Marine Radar from the on-screen boxes, the issue may be with the MAIN board inside the Processor unit. Consider replacing the MAIN board.
How to display six PI lines on Furuno FAR-2318?
If your Furuno Marine Radar is only displaying two PI lines when you want six, it may be due to an incorrect setting of the PI line interval or an inappropriate setting for the number of PI lines to display. Adjust the PI line interval and check the menu setting for the number of PI lines.
How to fix Furuno FAR-2318 Marine Radar if it cannot turn on?
If your Furuno Marine Radar cannot turn on, the possible causes are: a blown fuse, issues with the mains voltage/polarity, or a problem with the power supply board (PWR1 and/or PWR2) inside the Processor unit. To resolve this: * Replace the blown fuse. * Correct the wiring and input voltage. * Replace the faulty power supply board.
Why is the picture orientation incorrect on my Furuno Marine Radar?
If the picture orientation is incorrect on your Furuno Marine Radar, it could be due to the Rotary Encoder inside the antenna unit, the SPU board inside the antenna unit, or the MTR-DRV board inside the antenna unit. If the message 'NO HEADLINE SIGNAL' appears, check the heading line signal cable and board connections. If there are no problems with cables or connections, replace the faulty board.
What to do if Furuno FAR-2318 power is on but nothing appears on the monitor?
If the power is on but nothing appears on the monitor of your Furuno Marine Radar, the brilliance might be too low. Adjust the brilliance.
Why do marks and indications appear but no noise or echo on Furuno FAR-2318 Marine Radar?
If you adjust the GAIN with A/C SEA set at minimum and marks and indications appear but there is no noise or echo on your Furuno Marine Radar, it could be due to the IF amplifier or the signal cable between the antenna and processor unit. Consider replacing the IF amplifier or checking the continuity and isolation of the coaxial cable, disconnecting the plug and lugs at both ends before checking with an ohmmeter.
Why does my Furuno FAR-2318 Marine Radar show marks, indications, and noise but no echo?
If your Furuno Marine Radar shows marks, indications, and noise but no echo (and the transmission leak representing your own ship position is absent), possible causes include activation of the TX high voltage protection circuit, a faulty magnetron, or issues with the MD or SPU boards inside the antenna. To troubleshoot: 1. Reset the power to restore normal operation. 2. Check the magnetron current and replace the magnetron if necessary. 3. Replace the MD board. 4. Replace the SPU board.
How to fix Furuno FAR-2318 Marine Radar when the picture is not updated or frozen?
If the picture on your Furuno Marine Radar is not updating or is frozen, it could be due to the Rotary Encoder inside the antenna unit, the SPU board inside the antenna, or a video freeze-up. Try checking the connection of signal cables, replacing the SPU board, or turning the radar off and then on again.
Why does my Furuno FAR-2318 Marine Radar have poor sensitivity after tuning?
If your Furuno Marine Radar has poor sensitivity after tuning, it could be due to the second trace echo rejector being on or dirt on the radiator face. Try disabling the second trace echo rejector and cleaning the radiator face.
General| Brand | Furuno |
|---|---|
| Model | FAR-2318 |
| Category | Marine Radar |
| Language | English |
General guidelines and notices for using the manual and equipment.
Instructions for proper disposal of the product according to regulations.
Guidelines for disposing of used batteries safely.
Details hazards associated with RF radiation from the radar antenna.
Information about warning labels attached to the equipment.
Lists the models and configurations within the FAR-2xx8 series.
Defines terminology and usage examples for this manual.
Provides information on accessing software versions and program numbers.
Details function availability based on radar specification types.
Explains abbreviations used for different radar types.
Table showing function availability across different specification types.
Outlines plotter features available via software updates for fishing.
Lists and describes the signal processing functions of the radar.
Refers to website for CE/UKCA declarations and RoHS conformity.
Directs users to the website for China RoHS information.
Details the system configuration for X-band radars with CF antennas.
Details the system configuration for X-band radars with AF antennas.
Details the system configuration for S-band radars with TR-UP units.
Details the system configuration for X-band radars with TR-DOWN units.
Details the system configuration for S-band radars with TR-DOWN units.
Categorizes the different units used in the system configuration.
Provides important notes regarding system configuration and unit compatibility.
Describes the control units (RCU-014, RCU-015/RCU-016) for radar operations.
Details the procedure for powering the radar system on and off.
Explains how to adjust screen and echo brilliance from the control unit and on-screen.
Describes the three main areas of the radar system's on-screen display.
Explains how to open, close, and operate menus within the radar system.
Guides on accessing radar functions using on-screen box shortcuts.
Details how to use the cursor menu for various radar functions.
Explains how to view and change cursor data attributes and display formats.
Guides on assigning functions to the programmable function keys (F1-F4).
Explains how to customize various operation items to suit user needs.
Guides on selecting the source for ship's heading input data.
Details methods for entering own ship speed (automatic, manual, echo-referenced).
Guides on selecting the data source for own ship's position.
Explains how to adjust the local time and switch between UTC and local formats.
Guides on resetting and saving/loading user settings for radar functions.
Details procedures for starting and stopping radar transmission and antenna rotation.
Explains how to select tuning methods and perform manual tuning.
Guides on selecting and changing preset pulselengths for different ranges.
Explains how to adjust receiver sensitivity using the GAIN control.
Guides on reducing sea clutter using A/C SEA control.
Explains how to reduce rain clutter using AUTO RAIN and A/C RAIN controls.
Details how to use the interference rejector to reduce mutual radar interference.
Explains the echo stretch feature for enlarging targets to improve visibility.
Describes the echo averaging feature for reducing sea clutter and distinguishing targets.
Explains the ACE function for automatic sea and rain clutter reduction.
Guides on using the noise rejector to reduce white noise and improve S/N ratio.
Describes the wiper feature for reducing brilliance of weak signals and unwanted echoes.
Explains how to assign function keys to preset radar controls for specific situations.
Details how to enable or disable the rejection of second-trace echoes.
Describes the different orientation modes available for the radar display.
Guides on selecting the appropriate range scale for target observation.
Explains methods for measuring target range using fixed rings, cursor, or VRM.
Details methods for measuring target bearing using EBL keys or on-screen menu.
Explains how to assess collision risk using the offset EBL function.
Guides on measuring range and bearing between two selected targets.
Explains how to off-center the display to expand the view field.
Covers displaying target trails in true or relative motion.
Explains the target analyzer function for identifying dangerous targets.
Guides on setting target alarms for specific areas and types of alerts.
Explains how to use Parallel Index lines for maintaining a constant distance.
Guides on using the net cursor for depicting fishing nets.
Explains how to use the zoom function to enlarge areas of interest.
Covers using various marks like heading line, stern mark, and north mark.
Guides on inscribing and erasing drop marks for navigation points.
Explains how to select and customize brilliance and color schemes.
Guides on displaying and setting up navigational data like wind and depth.
Explains how to set up the information box for target data and nav data.
Details how to preset antenna and display combinations for interswitch functionality.
Explains how to activate and check the radar's performance monitor.
Guides on changing the reference position for measurements and markers.
Explains how to set up the anchor watch feature to alert when the ship drifts.
Provides information on alert priorities, categories, and how to interpret them.
Guides on using the icing prevention feature to rotate the antenna.
Explains how to select different echo display modes (CIRCLE, WIDE, ALL).
Covers formatting, handling, and compatible SD cards for data storage.
Explains how to use the built-in screenshot feature with an SD card.
Guides on enabling or disabling the watch alert for monitoring the radar.
Details how to enable and configure the dual radar display function.
Explains how to output echo data to a PC for wave analysis.
Describes the Doppler feature for clutter reduction and target detection.
Covers general radar principles like minimum and maximum range.
Discusses differences in performance between X-band and S-band radars.
Explains bearing and range resolution factors in radar.
Details the factors affecting the accuracy of bearing measurements.
Describes methods for measuring target range using radar.
Explains common types of false echoes and their causes.
Details the functionality and display of SART signals on the radar.
Describes RACON signals and their appearance on the radar display.
Explains the purpose and function of the Radar Target Enhancer.
Discusses the characteristics and display of solid-state radar echoes.
Important warnings and cautions before using the target tracking feature.
Describes the specific keys used for target tracking on the control unit.
Explains how to show or hide TT symbols and their meaning.
Guides on selecting manual, automatic, or combined target acquisition modes.
Details the process of acquiring and tracking targets, both manually and automatically.
Explains how to input own ship's speed for TT and stabilization.
Procedures for canceling tracking for individual or all targets.
Information on lost target alerts and how to set the lost target filter.
Covers adjusting brilliance and color of TT symbols.
Explains displaying and removing target data from the data display area.
Guides on assigning preset names to TT targets for easier identification.
Describes vector modes and stabilization options for target display.
Explains the display of past target positions and plotting intervals.
Details how to enter set and drift corrections for improved vector accuracy.
Covers setting CPA and TCPA ranges for collision risk assessment.
Explains how to enable and set up acquisition zones for target alerts.
Describes simulating own ship maneuvers to assess target movements.
Lists system messages related to TT alerts, their priority, and meaning.
Guides on using the simulation mode for familiarization training.
Explains the criteria used for selecting and acquiring targets.
Discusses various factors that can affect target tracking accuracy.
Describes the control keys specific to AIS operation.
Explains the indications and remarks within the AIS box.
Guides on selecting display modes for AIS symbols (OFF, FILT, ALL).
Explains the meaning of various AIS symbols displayed on the screen.
Details how to filter unnecessary AIS objects using the AIS Display Filter menu.
Explains how to activate sleeping AIS targets manually.
Guides on limiting AIS auto-activation based on range, speed, and class.
Procedures for sleeping individual or all AIS targets to manage screen clutter.
Instructions for inputting voyage data like nav status, ETA, and destination.
Explains how to display basic and expanded AIS data for objects.
Covers adjusting brilliance, size, and color of AIS symbols.
Explains the display of past positions for activated AIS targets.
Details AIS lost alerts and how to set the AIS lost filter.
Describes how to set the Rate Of Turn limit for AIS symbol heading lines.
Guides on setting CPA and TCPA ranges for AIS collision alarms.
Explains how to associate TT and AIS targets for unified display.
Provides instructions on viewing own ship's static data.
Covers creating, saving, transmitting, and viewing AIS messages.
Lists AIS system messages, their priority, and meanings.
Describes the six available orientation modes for the radar display.
Guides on selecting different types of markers for radar maps.
Explains how to choose the location for inscribing markers.
Details how to create and manage radar maps with symbols and lines.
Explains how to mark prominent targets or points of interest.
Guides on adjusting the own ship mark shape for realism.
Covers displaying marks received from an ECDIS on the radar.
Explains how to show or hide tracks for own ship and targets.
Explains how to manage waypoints, including setting data sources and entering them.
Explains how to set, edit, display, and delete routes.
Details chart functions available for A/B/W-types with Radar Plotter.
Outlines a regular maintenance program for the electronic system.
Details the procedure and fuse types for replacing fuses in the equipment.
Provides estimated lifetimes for consumable parts like magnetrons and motors.
Explains how to clean the trackball for normal operation.
Offers troubleshooting procedures for common operational issues.
Describes hardware and software troubleshooting for qualified personnel.
Details how to execute diagnostic tests for circuit boards and components.
Guides on checking input sentences to the radar for troubleshooting.
Explains how the system automatically uses backup sensors if a primary sensor fails.
To Next Page
