Fusion MS-NRX200i Instruction Manual

®
Fusion
™
MS-NRX200i Installation
Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Tools Needed
• Phillips screwdriver
• Drill
• 2.5 mm (
3
/
32
in.) drill bit
• 50 mm (2 in.) hole saw
• Marine sealant (optional)
Connection Considerations
You can connect the Fusion NRX200i remote control to the
Fusion BB300 stereo using a Fusion remote control network or
an existing NMEA 2000
®
network.
NMEA 2000 Connection Considerations
The Fusion MS-NRX200i remote connects to a NMEA 2000
network on your boat using the attached NMEA 2000 cable and
included connector. Through the NMEA 2000 network, you can
control a connected Fusion BB300 device.
You can connect an unlimited number of remote controls to the
NMEA 2000 network to control a Fusion BB300 device, but you
must build a properly balanced NMEA 2000 network.
Item Description
À
Fusion BB300 device
Á
Compatible chartplotter
Â
Fusion NRX200i remote control
Ã
12 Vdc power source with an ignition or in-line switch
Ä
Fusion BB300 NMEA 2000 drop cable
This can be extended to a maximum length of 2 m (6 ft.) using a
standard NMEA 2000 cable.
Å
NMEA 2000 drop cable
Item Description
Æ
Fusion NRX200i remote control drop cable.
This can be extended to a maximum length of 2 m (6 ft.) using a
standard NMEA 2000 cable.
Ç
NMEA 2000 power cable
È
NMEA 2000 terminator or backbone cable
É
NMEA 2000 T-connector
Remote Control Network Connection Considerations
You must use the red, powered drop cable included with the
Fusion MS-BB300R stereo and remote bundle to create this
network.
You can connect one Fusion BB300 stereo and up to three
Fusion NRX200i remote controls to a Fusion remote control
network. If you are connecting more than three remote controls
to the stereo, you must connect to a full NMEA 2000 network.
Item Description
À
Fusion BB300 stereo
Á
Fusion NRX200i remote control
Â
Red, powered drop cable, supplied with Fusion MS-BB300R
stereo and remote bundle
Ã
NMEA 2000 female terminator
Ä
NMEA 2000 T-connector
Å
NMEA 2000 backbone cable, 6 m (20 ft.)
Æ
NMEA 2000 inline terminator
Mounting Considerations
When selecting a mounting location, observe these
considerations.
• The device must be mounted in a location where there is at
least 75 mm (3 in.) of clearance behind the mounting surface
and you can access the controls after it is mounted.
• If you want to mount the device outside the boat, it must be
mounted in a location well above the waterline, where it is not
submerged.
• If you want to mount the device outside the boat, it should be
mounted in a location where it will not be damaged by a
docks, pilings, or other pieces of equipment.
Mounting the Remote Control
1
At the mounting location, use a 50 mm (2 in.) hole saw to cut
through the mounting surface.
2
Place the remote control in the cutout and mark the pilot
holes.
3
Remove the remote control from the cutout, and using a
2.5 mm (
3
/
32
in.) drill bit, drill the pilot holes.
4
Apply marine sealant around the cutout (optional).
5
Place the gasket on the back of the remote control.
6
Feed the attached NMEA 2000 cable through the cutout.
7
Place the remote control in the cutout.
April 2015
Printed in Thailand 190-01914-03_0A

Fusion MS-NRX200i Specifications

General

Brand	Fusion
Model	MS-NRX200i
Category	Remote Control
Language	English