FUTABA T26SZ - Page 150

150
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŷƕƌƐŃƐƌƛŃŔŒŕ
[Corresponding model type]: Glider, general
These functions call the ailerons, elevators, and
ÀDSVFDPEHUÀDSVEUDNHÀDSVWULPR൵VHWUDWHV
SUHVHWDFFRUGLQJWRWKHÀLJKWVWDWH
The amount of ailerons, elevator, and flaps
FDPEHUÀDSEUDNHÀDSWULPR൵VHWFDQEHVHWWRD
switch.
As an example 7ULPPL[ can be set up for
ODXQFKLQJZLWKVSHHGÀDSVDQGDLOHURQVGURSSHG
and a slight amount of up elevator. 7ULPPL[
 can be used for high speed flying, with both
DLOHURQVDQGVSHHGÀDSVUHÀH[HGVOLJKWO\DQGDELW
of down elevator.
7KHWULPIXQFWLRQVFDQEHDFWLYDWHGGXULQJÀLJKW
by setting a switch. To prevent sudden trim
FKDQJHVZKHQVZLWFKLQJÀLJKWFRQGLWLRQVDGHOD\
can be set to provide a smooth transition between
the two. Trim mix 2 will have priority over Trim
mix 1.
Theoffsetrateofailerons,flapsandelevatorscanbeadjusted.
Taptothecorrespondingsettingitem.Adjusttherate.
([DPSOH
1. Move to the [INH] item
.
Set the trim mix function to
[ON].
*When separating the settings for each condition, move to
the [Group] item and set it to [Single].
2. Select the ON/OFF switch.
3. Select the [Manual] or [Auto] mode.
In the [Auto] mode, also select an auto SW. This
switch can be linked to a stick, etc.
<Speed>
In: The operation speed at switch ON can be set.
Out: The return speed at switch OFF can be set.
<Fine Tuning>
The offset rate can be varied in the Fine Tuning
numeric range set at screen by VR, etc. selection.
<Condition Delay>
:KHQÁLJKWFRQGLWLRQVDUHVHWWKHRSHUDWLRQVSHHG
can be set for each condition. Condition delay
operation can be interrupted and each rudder
quickly returned to its original position by selecting a
cut switch.
ŏ6HOHFW>7ULPPL[RU@DWWKHPRGHOPHQX
and call the setup screen shown below.
Whenusingthisfunction,
Tap[INH].(ONis
displayed.)
TheON/OFFswitchof
mixingischosen.
Manual/Automode
selection
Manual:Switchesthe
functionON/OFFby
switch
Auto:Trimmixfunction
callcanbelinkedtoa
stick,etc.Astickswitch,
etc.separatefromthe
functionON/OFFswitchis
set.
Conditiondelaysetting
Conditiondelaycut
switch
Inspeed
Outspeed
（First）0 〜 27（Slowly）
（First）0 〜 27（Slowly）
*Thedisplayscreenisanexample.Theactual
screendependsontheModelType.
WhenafinetuningVRisset,
thetrimratesofailerons,
flapsandelevatorscanbe
adjusted.
Tonextpage
ŏ5HWXUQWR0RGHOPHQX
Thevalueinsidethe
parenthesesshowsthe
currentrudderposition.