Why are icons flashing and alarm sounding on my Galleon 3K?
This indicates an overload. Try removing some of the connected devices from the UPS output. If the UPS is locked in Bypass mode after repetitive overloads, remove excess loads, then shut down the UPS and restart it.
What to do if Galleon 3K UPS shows no indication and alarm even though the main is normal?
First, check that the input power cord is firmly connected to the mains. Also, verify that the AC input power cord is correctly plugged into the AC input, and not the UPS output.
What does it mean when fault code 43 is shown on Galleon 3K UPS?
Fault code 43 indicates that the Galleon UPS shut down automatically due to an overload at the output. Remove some of the connected devices from the UPS output and then restart the UPS.
Why is the battery backup time shorter than expected on my Galleon 3K UPS?
This could be because the batteries are not fully charged. Charge the batteries for at least 5 hours and then check their capacity. If the problem persists, contact your dealer.
What does it mean when the icon and warning code are flashing on my Galleon UPS?
This could be due to several reasons: * The EPO function may be activated. Try setting the circuit in a closed position to disable the EPO function. * The line and neutral conductors of the UPS input may be reversed. Rotate the mains power socket by 180° and then connect it to the UPS system. * The external or internal battery might be incorrectly connected. Check that all batteries are connected well.
What does fault code 14 mean on a Galleon UPS?
Fault code 14 indicates that the Galleon UPS shut down automatically because a short circuit occurred on the UPS output. Check the output wiring and the connected devices for a short circuit.
What does fault code 28 mean on a Galleon 3K?
Fault code 28 means the battery voltage is too low or the charger is faulty. Contact your dealer.
What does fault code 27 mean on a Galleon 3K UPS?
Fault code 27 means the battery voltage is too high or the charger is faulty. Contact your dealer.
What does fault code 45 mean on a Galleon 3K UPS?
Fault code 45 indicates that the charger does not have output and the battery voltage is less than 10V/PC. Contact your dealer.
What does it mean when my Galleon UPS shows fault code 01, 02, 03, 11, 12, 13 or 41?
A UPS internal fault has occurred. Contact your dealer.
Steps to install the UPS: remove front panel, reconnect battery wires, replace front panel. Can be desk or rack-mounted.
Steps for UPS setup: input connection to grounded receptacle, output connection to critical/non-critical loads.
Steps for hot-swappable battery replacement: remove front panel, disconnect wires, remove battery box, replace batteries, re-connect wires, replace front panel.
Explains the three parameters for UPS configuration and alternatives for Parameter 1.
Allows setting the output voltage for different UPS models and voltage ranges.
Troubleshooting steps for the UPS showing no indication or alarm when the main is normal.
Troubleshooting steps when the EPO function is activated and the UPS displays related icons and alarms.
Troubleshooting steps when UPS input conductors are reversed, causing specific icons and alarms.
Troubleshooting steps for incorrect external or internal battery connection, indicated by specific icons and alarms.
Troubleshooting for fault code 27 and BATT. FAULT icon, indicating high battery voltage or charger fault.
Troubleshooting for fault code 28 and BATT. FAULT icon, indicating low battery voltage or charger fault.
Troubleshooting for overload conditions indicated by specific icons and alarms, including bypass mode.
Troubleshooting for fault code 43 and OVER LOAD icon, indicating UPS shutdown due to output overload.
Troubleshooting for fault code 14, indicating UPS shutdown due to output short circuit.
Troubleshooting for UPS internal faults (codes 01, 02, 03, 11, 12, 13, 41) leading to bypass or no power.
Troubleshooting for fault code 45, indicating charger or low battery voltage issues.
To Next Page
General