To Next PageTo Next PageWhat does 'Identical IP1 modules Identical IP2 modules' mean on GE HEALTHCARE E-PSM Medical Equipment?
If the GE HEALTHCARE Medical Equipment displays 'Identical IP1 modules Identical IP2 modules', it means the monitor detects the same IP channel from two or more modules. To resolve this, remove one of the modules providing the identical IP channel.
What to do if the GE HEALTHCARE E-PSM Medical Equipment displays NIBP cuff loose?
If the GE HEALTHCARE Medical Equipment shows 'NIBP cuff loose', it could be due to several reasons. First, ensure that the hose and cuff are properly connected. If they are, check if the cuff is loosely wrapped and tighten it. Also, inspect for any leakage inside the shield, in the Patient connector panel, or in the tubings connecting to the module; fix if necessary. Furthermore, check for leakage in the cuff or hose, and replace them if needed. Leakage inside the module is another possibility, so check the internal tubing and fix it if necessary. Lastly, if the pump isn't working, check the pump connector; if it's okay, replace the NIBP Pump Unit.
What causes NIBP air leakage in GE HEALTHCARE E-PSM?
If the GE HEALTHCARE Medical Equipment is showing 'NIBP air leakage', it could be due to a leaking hose or cuff, in which case you should replace the cuff. If the cuff connector is damaged, replace it, especially if the fault is in the hose connector. Check for a damaged or missing O-ring and replace it if necessary. Also, inspect the hose double connector for damage and replace the NIBP cuff hose if needed. Examine the tubes connecting the patient connector panel and the module for leakage, and check the tubes inside the module, replacing the whole tubing if there's leakage. If a tube is disconnected or damaged, fix the connections. Finally, if the manifold is leaking or the tubes/valves are damaged, replace them.
What to do if GE HEALTHCARE Medical Equipment displays 'Leads off'?
If the GE HEALTHCARE Medical Equipment displays 'Leads off', this indicates that one or more lead wires or electrodes are disconnected. In this case, check the lead wire and electrode connections.
What does 'XX/YY lead off' mean on GE HEALTHCARE E-PSM?
If the GE HEALTHCARE Medical Equipment displays 'XX/YY lead off', it indicates that one or more lead wires or electrodes are disconnected. To resolve this, check the lead wire and electrode connections.
What does 'Px over range >320mmHg' mean on GE HEALTHCARE E-PSM?
If the GE HEALTHCARE Medical Equipment displays 'Px over range >320mmHg' or '>43 kPa', it means the measured pressure exceeds the upper specification limit of 320 mmHg / 43 kPa, or the transducer is not zeroed correctly. The measurement range is between -40 mmHg and 320 mmHg. Zero the invasive pressure channel x.
Why is the NIBP measurement removed on GE HEALTHCARE E-PSM Medical Equipment?
If the GE HEALTHCARE Medical Equipment displays 'NIBP measurement removed', it means that the module is disconnected. To solve this, reconnect the module.
What does 'Px under range
If the GE HEALTHCARE Medical Equipment displays 'Px under range
What to do if GE HEALTHCARE Medical Equipment displays 'Incompatible probe'?
If the GE HEALTHCARE Medical Equipment displays 'Incompatible probe', it means that an incompatible SpO2 probe is detected by the monitor. To fix this, replace the SpO2 probe with a compatible one.
Why does GE HEALTHCARE E-PSM Medical Equipment show 'Measurement off'?
If the GE HEALTHCARE Medical Equipment shows 'Measurement off', it could be due to several reasons: the ECG cable is disconnected, the module is disconnected, impedance respiration PW or WF is not configured on the screen, one or more leads required for impedance measurement are disconnected, or Impedance Respiration Measurement is set to “Off”. To resolve this, connect the ECG cable, connect the module, configure either the ImpResp waveform or Resp parameter window on the monitor screen, connect any disconnected lead wires and/or electrodes, and set Impedance Respiration Measurement “On” from the Setup tab in the Impedance respiration menu.
General| Brand | GE HEALTHCARE |
|---|---|
| Model | E-PSM |
| Category | Medical Equipment |
| Language | English |
Instructs to complete electrical safety tests as per the monitor's technical manual.
Describes the setup, connections, and configuration needed for functional testing of modules.
Explains the steps for temperature calibration, including required tools and procedures.
Outlines when and how to perform NIBP calibration, including required equipment and procedure.
Provides step-by-step instructions for disassembling and reassembling these specific module types.
Instructs to complete electrical safety tests as per the monitor's installation checkout.
Instructs to complete electrical safety tests as per the monitor's technical manual.
Describes test setup, connections, and monitor configuration for functional checks.
Details the procedure for calibrating invasive pressure channels, including required tools and connections.
Details the procedure for calibrating invasive pressure channels, including required tools and connections.
Details the procedure for adjusting sample flow rate using a mass flowmeter and calibration software.
Details the procedure for adjusting sample flow rate using a mass flowmeter and calibration software.
Details required equipment and calibration check procedures for NIBP.
Explains the steps for temperature calibration, including required tools and procedures.
Explains gas calibration procedures, including required tools, connections, and the calibration process.
Explains gas calibration procedures, including required tools, connections, and the calibration process.
Provides initial troubleshooting hints to localize problems, checking compatibility and module connections.
Details essential precautions for handling components susceptible to ESD damage to prevent failure.
Details procedures for disassembling and reassembling the E-P, E-PT, or E-PP modules.
Details procedures for replacing the front cover and the NMT board.
Details procedures for replacing components like the battery, labels, and boards.
