GE HEALTHCARE E-PSM User Manual

GE Healthcare
Module Frames and Modules
Technical Manual
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
All specifications subject to change without notice.
English
Order code
#2062973-004 paper
October 5, 2016
© 2013 - 2016 General Electric Company. All rights reserved.

GE HEALTHCARE E-PSM Specifications

General

Brand	GE HEALTHCARE
Model	E-PSM
Category	Medical Equipment
Language	English

Summary

3 Maintenance and checkout

3.3 Electrical safety tests

Instructs to complete electrical safety tests as per the monitor's technical manual.

3.4 Functional check

Describes the setup, connections, and configuration needed for functional testing of modules.

4 Calibration and adjustments

4.2 Temperature calibration

Explains the steps for temperature calibration, including required tools and procedures.

4.3 NIBP calibration

Outlines when and how to perform NIBP calibration, including required equipment and procedure.

5 Troubleshooting

6 Disassembly and reassembly

6.2 Disassembling and reassembling procedure, E-PRESTN, E-PRETN, E-RESTN

Provides step-by-step instructions for disassembling and reassembling these specific module types.

7 Service parts

7.2 E-PRESTN, E-PRETN, E-RESTN

7.2 Continuous Cardiac Output Module, E-PiCCO

Maintenance and checkout

3.1 Replacement of planned maintenance parts

3.2 Electrical safety tests

Instructs to complete electrical safety tests as per the monitor's installation checkout.

3.2 Electrical Safety Tests

Instructs to complete electrical safety tests as per the monitor's technical manual.

3.3 Functional check

Describes test setup, connections, and monitor configuration for functional checks.

3.3 Functional checkout

3.3 Checkout procedure

Calibration and adjustments

4.1 Invasive pressure calibration

Details the procedure for calibrating invasive pressure channels, including required tools and connections.

4.1 Invasive Pressure Calibration

Details the procedure for calibrating invasive pressure channels, including required tools and connections.

4.1 Sample Flow Rate Adjustment

Details the procedure for adjusting sample flow rate using a mass flowmeter and calibration software.

4.1 Sample flow rate adjustment

Details the procedure for adjusting sample flow rate using a mass flowmeter and calibration software.

4.1 NIBP

Details required equipment and calibration check procedures for NIBP.

4.2 Temperature Calibration

Explains the steps for temperature calibration, including required tools and procedures.

4.2 Gas Calibration

Explains gas calibration procedures, including required tools, connections, and the calibration process.

4.2 Gas calibration

Explains gas calibration procedures, including required tools, connections, and the calibration process.

4.2 Analog outputs

Troubleshooting

5.2 Troubleshooting checklist

Provides initial troubleshooting hints to localize problems, checking compatibility and module connections.

5.2 Device information and diagnostics

5.3 Service Interface

5.3 Service interface

5.2.1 Gas sampling system troubleshooting

5.3 Troubleshooting checklist

5.3 Problems and solutions

5.4 Error messages

Disassembly and reassembly

6.1 Disassembly guidelines

6.1.1 ESD precautions

Details essential precautions for handling components susceptible to ESD damage to prevent failure.

6.2 Disassembling and reassembling procedure

Details procedures for disassembling and reassembling the E-P, E-PT, or E-PP modules.

6.2 Disassembly and reassembly procedure

Details procedures for replacing the front cover and the NMT board.

6.3 Replacement procedures

Details procedures for replacing components like the battery, labels, and boards.

Service parts

7.2 Cardiac Output Module, E-COP

7.2 Pressure and Pressure Temp Modules E-P, E-PT, E-PP

7.2 Masimo compatible Saturation Module, E-MASIMO

7.2 Spare parts for E-CAiOVX, E-CAiOV, E-CAiO, E-COVX, E-COV, E-CO

7.2 Single-width Airway Module, E-miniC

7.2 Entropy Module, E-ENTROPY-01

7.2 EEG Module, E-EEG

7.2 BIS Module, E-BIS

7.2 Spare parts for E-NMT-01

7.2 Parts

7.3 Cardiac Output Module, E-COPSv