www.GEAppliances.com
COOLMODE
RemoteControl
l. Px_ssCOOLpad.
2.P*_ssLOW,IVIEDor HIpads to set desired fire speed.
3.Px_ssdieINCREASEA/DECREASETpadstoset the
desix_d temperature 60°Fto 85°F in l°Fincrements.
ControlPanel
l. Pxess d_e MODEpad until tile COOLindicator lig]lt is
lit and the LOW,MEDor Hlindicator light is lit fbr
dm (]esix_(] thn speed.
2. Px_ss the INCREASE&/DECREASET pads to set the
(]esix_(] temperature 60°F to 85°F in l °F increments.
A them/ostat is used to maintain tile room
temperature. Tile compressor will e}cle on and off
to keep tile room at tile set level of comtbrt. Set die
thermostat at a lo_r nm-nber and die indoor air will
become coolex; Set tile themlostat at a big]mr number
and tile indoor air will become _mnex;
NOTE:ff theair conditioner is off andis then turned on
while set toCOOL,it will take approximately3minutes for
the compressorto start and cooling tobegin.
CoolingDescriptions
ForNormal Cooling--Select the COOLmode and
HIGHor MEDtbn with a middle set temperature.
ForMaximumCooling--Select tile COOLmode
and HIGHtim with a lowerset temperatm_.
ForQuieter& NighttimeCooling--Select tile COOLmode
and LOWfbnwid_a middle set temperature.
NOTE:If youswitch froma COOLsettingtoOFFerto
afansetting waitatleast3minutesbeforeswitchingback
toaCOOLsetting.
Fan Switch
Tile thn switch is located behind tile ti'ont grille on the
control box. Access through a hole in control box.
_A]mn set at CYCLE(do_n) tile thn e_cles on and off.
When set at CONT(continuous, up) tile tim runs all tile
time prodding a rnox_ balanced mmperatm_. The unit
is shipped in tile CONTsetting.
FAN MODE
Use tile FANmode to pro\ide _drcirculation and
filtering without cooling. Since tim only settings do not
provkle cooling, a tempenmlre setting will not be
displa}ed.
RemoteControl
Px_ss FANpad. Press LOW,MEDor HI pads to set
desix_d thn speed.
ControlPanel
Px_ss die MODEpad until tile FANindicator light is lit
and tile LOW, MEOor HIindicator light is lit tbr the
desix_d tan speed.
Vent Control
T]_e vent control is located behind tile ti'ont grille on
tile right side of tile air (fischarge area. "_lmn set at
CLOSE,only tile air inside the room will be circulated
and conditioned. When set at OPEN,some inside air is
exhausted outside.
TO opell or close tile vent:
l. Remove tile ti'ont grille.
2. Remove tile vent card scx_.
3. Remove vent card, turn it over and replace it b}
locating rear hole in card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunitleavesthe factoryset at theCLOSEposition.
._Locating i_oie
Screwhole "_.
OPENposition
(Meshendtowardback)
Screwha
CLOSEposition
(Meshendtowardfront)
A# Direction
Horizont_fl lomers
on d_e fi'ont grille let
you control tile air
(lirection up and
doP_I/.
Remove the i]?ont
grille to a(!just the
vertical louvers
side-to_ide to
(fix_ct the air
left or fight.
To Next Page
Loading...
