3-Wire System for Electric Dryers-DO NOT use for Mobile Home Installations
F_ Remove tile screws securing tile terminal bh)ck
a((ess (over and the strain relief mounting
bra(ket lo(ated on the ba(k of din dxyer upper
CoI'neI'.
[_] Attach tile power cord neutral (center wire)
conductor to the silver-colored center terminal
on the terminal bh)ck. Tighten the screw
sectlrely.
[_ Install a UL-approved suain reliefinto the power
(ord enuy hole of din mounting bra(ket. Use
a smfin relief which attaches to the mounting
bracket with a nut. Finger-tighten the nut only
at this time.
F_ Thread a UI 7approved 30A, 240V, 3 # 10AW(;
minimum copper condu(tor power cord through
the strain relieL
Green (
Silverterminal
F_ Attach tile remaining two power cord outer
conductors to tlle outer b{ass-colored terminals
on tile terminal bh)ck. Tighten both screws
securely.
A WARNIN&Do not make a sharp bend or crimp
_firing/conductor at connections.
F_ Reauach tile strain relief mounting bracket to
tlle back of din &yer with two screws. Tighten
s(rews se(tliely.
F_ Tighten the screws securing the cord restraint
firmly against the power (ord.
Greenneutral
groundwire Nut
[_ Tighten tile strain relief nm securely so that tile
strain relief does not turn. •
[_ Reinstall tile terminal bh)ck access cover.
Usecopper Strarelief
conductorsonly. mounting bracket
Po'_wercord
4-Wire System for Electric Dryers--MUST be used for Mobile Home Installations
F_ Remove tile screws securing tile terminal bh)ck
access cover and the stiain relief mounting
bracket located on tile back of din &yer upper
CoI'neI',
[_ Install a UITapproved strain relief in the enuy
hole of the mounting bra(ket. Use a strain relief
whkh attaches to the mounting bra(ket with a
nut. Finger-tighten the nut only at this time.
F_ Remove tile green neutral ground wire fiom tile
Y Y
green ground s(rew lo(ated above the terminal
blo(k.
Typical4 t/'l w _ Black240V
conductor| I I ]
receptacle_. '=11 J Typical ._(t.
4 conductorcord J,_=" Whiteneutral
"_Red 240V
--Green ground
F_ Thread a UL-approved 30A, 240V, 4 # 10AW(;
mmml m _ on o_ ox_
• " u coppec duct p _ecordthrough
tlle strain relief.
[_ Attach the green power cord ground wire to the
cabinet _dth the green ground screw.
[_ Auach tile white (neutral) power cord
condu(tor fioln tile power cord and tile green
ground wire fiom tile (hyer harness to the silver-
(oh)red (enter terminal on the terminal blo( k.
Tighten the screw securely.
F_] Auach tile red and black power cord conductors
to tile outer brass-coh)red terlninals on the
terminal bh)ck.
Greenpowercordgroundwire
Greenground _ /
screw "_/a_//_ Silverterminal
(____J_ _. _-,,_=====Te rmina, block
Green neutral _ _/"_,
grou,,dw,re B,ack
I_"'_ °//_Wbite Nut
/1 _// ,, Tighten nut to
Red __k k_/"A tb'ese tbrea ds
/4. W/
_a- /_q relief " 2"-_5::s_
Powercord_ _ mounting?_NN
bracket
A WARNING:Donot make a sharp bend or crimp
wiring/conductor at the connections.
[_ Tighten the screws securing tile cord restraint
fi{mly against tile power c(ird.
[_ Tighten the suain relief nut securely so the
strifin relief does not turn. •
[_ Reinstall the terminal block access cover.
17
To Next Page
Loading...
