To Next PageTo Next PageWhat to do if the start status indicator light is flashing on my GE DDT 595?
If the start status indicator light is flashing on your GE Dishwasher, it means the door was opened or the cycle was interrupted. To restart, press the Start button once and close the door within 4 seconds. If you want to cancel the cycle while the dishwasher is running, press the Start button a second time.
Why does my GE Dishwasher beep once every minute?
If your GE Dishwasher is beeping once every minute, it's a reminder that the door has been left open during operation. To stop the beeping, press the Start button and close the door.
What to do if GE DDT 595 Dishwasher display shows “LEAK DETECTED”?
If your GE Dishwasher displays “LEAK DETECTED”, it means a possible leak has been detected. Call for service.
Why is my GE Dishwasher beeping at the end of the cycle?
If your GE Dishwasher is beeping at the end of the cycle (on some models), this is normal. The dishwasher will beep twice at the end of the cycle. To turn off the double beep indicator (or re-activate it if it was previously turned off), press the Heated Dry button 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been turned on or off.
Why is there detergent left in the dispenser cups of my GE Dishwasher?
If detergent is left in the dispenser cups of your GE Dishwasher, it's likely that dishes or utensils are blocking the detergent cup. Reposition the dishes to allow water from the lower spray arm to flush the detergent cup. Also, reposition tall utensils or heavy silverware that may be preventing the dispenser cup door from opening, and avoid placing large bowls or pots directly under the detergent dispenser.
How to remove black or gray marks on dishes from GE DDT 595?
If you notice black or gray marks on dishes from your GE Dishwasher, it's likely that aluminum utensils have rubbed against the dishes. Remove the marks with a mild, abrasive cleaner.
How to clean stained tub interior in GE DDT 595?
If your GE Dishwasher has a stained tub interior, and you see a white film on the inside surface, it's likely due to hard water minerals. GE Appliances recommends using Finish® Jet-Dry® Rinse Aid to help prevent these deposits. You can also run the dishwasher with citric acid to remove mineral deposits. Citric acid (Part number: WD35X151) can be ordered through GE Appliances Parts. Alternatively, purchase Finish® Dishwasher Cleaner and follow the directions on the label.
What to do if water won’t pump out of my GE Dishwasher?
If water won’t pump out of your GE Dishwasher tub, it's likely that the drain is clogged. If you have an air gap, clean it. If the dishwasher drains into a disposer, run the disposer to clear it. Check to see if your kitchen sink is draining well; if not, you may need a plumber.
Why do the control panel lights go off on my GE DDT 595 Dishwasher?
If the control panel lights on your GE Dishwasher go off while you're setting the controls, it means there was too much time between touching the selected buttons. Each button must be touched within 30 seconds of the others. To relight the panel, touch any button again or open the door and unlock (top control).
General| Type | Built-In |
|---|---|
| Control Type | Electronic |
| Dishwasher Interior | Stainless Steel |
| Energy Star Certified | Yes |
| Soil Sensor | Yes |
| Third Rack | No |
| Stainless Steel Tub | Yes |
| Racks | 2 |
| Lower Rack Features | Adjustable tines, fold-down tines |
Key safety instructions and warnings for appliance operation.
Guidelines for safe installation, grounding, and servicing of the dishwasher.
Basic safety measures to follow during dishwasher use to prevent injury.
Specific warnings regarding water heater gas and child entrapment risks.
Instructions for properly loading racks and silverware for best wash results.
Solutions for common problems like error codes, poor cleaning, and leaks.
Details on what is covered under the limited one-year warranty.
