What to do if my GE Ranges oven will not self-clean?
If your GE Ranges oven will not self-clean, it could be because the temperature is too high to start a self-clean operation. Allow the oven to cool down and then reset the controls. Also, ensure that the oven controls are properly set by referring to the Cleaning the Oven section.
What to do if my GE Ranges oven door will not open after a clean cycle?
If your GE Ranges oven door won't open after a clean cycle, it's likely because the oven is still too hot. Allow the oven to cool below the locking temperature, and then try opening the door again.
What to do if my GE Ranges oven does not work?
If your GE Ranges oven isn't working, first check if a fuse in your home has blown or the circuit breaker has tripped, and replace the fuse or reset the breaker. Also, the oven controls might be improperly set, so consult the Using the Oven section. Finally, make sure that the oven is not in Sabbath Mode, referring to the Special Features section.
What to do if my GE JB620 clock and timer do not work?
If the clock and timer on your GE Ranges are not working, it could be due to a blown fuse or tripped circuit breaker in your home. Replace the fuse or reset the circuit breaker. Also, ensure the range is fully plugged into a properly grounded electrical outlet. If the issue persists, refer to the Using the kitchen timer section.
How to stop my GE JB620 Ranges from smoking during self-clean?
If you experience excessive smoking during clean cycle with your GE Ranges, press the Cancel/Off pad, open the windows to rid the room of smoke, wait until the LOCKED light goes off, wipe up the excess soil, and reset the clean cycle.
Why is my GE JB620 Ranges food not broiling properly?
If food isn't broiling properly in your GE Ranges, ensure the oven controls are set correctly for broiling mode. Check the Cooking Guide for proper rack positioning. Make sure the food is not being cooked in a hot pan and that you are using cookware specifically designed for broiling. If using aluminum foil, make sure it's properly fitted and slit as recommended. If your area has low voltage, preheat the broil element for 10 minutes.
Why are my GE JB620 Ranges surface units not maintaining a rolling boil?
Your GE Ranges surface units may not maintain a rolling boil due to improper cookware. Use flat-bottomed pans that match the diameter of the surface unit. In areas with low voltage, cover the pan with a lid to help retain heat until the desired temperature is reached.
What does it mean if “F— and a number or letter” flash in the display of my GE JB620?
If you see “F— and a number or letter” flashing on your GE Ranges display, it indicates a function error code. Press the Cancel/Off pad and allow the oven to cool for one hour before putting it back into operation. If the error repeats, disconnect all power to the oven for at least 16 seconds and then reconnect power. If the function error code repeats, call for service.
Why doesn't food broil properly in my GE JB620?
Make sure you select the appropriate broil mode. See Cooking Guide for rack location suggestions. Make sure cookware is cool. Use a pan specifically designed for broiling! If using aluminum foil conform to pan slits. Preheat the broil element for 10 minutes.
Why does my GE Ranges take so long to preheat?
Remove items to reduce preheat time. Adding more racks to the oven will cause the oven to take longer to preheat. Remove some racks. The different cooking modes use different preheat methods to heat the oven for the specific cooking mode. Some modes will take longer than others (i.e. convection bake).
General| Number of Burners | 4 |
|---|---|
| Self-Cleaning | Yes |
| Color | Black |
| Fuel Type | Electric |
| Burner Type | Radiant |
| Cooktop Material | Ceramic Glass |
| Type | Freestanding |
| Cooktop Surface | Smooth |
| Ignition Type | Electric |
To Next Page
