GE PFW870 User Manual (English)

Questions and Answers:

J
James SchroederAug 3, 2025
Why is my GE PFW870 not draining, spinning, or tumbling?
- K
  Kathryn SimpsonAug 3, 2025
  If your GE Washer is not draining, spinning, or tumbling, it could be due to several reasons. First, the load might be unbalanced; try redistributing the clothes and running a Rinse & Spin cycle. If you're washing a small load with heavy and light items, increase the load size. Also, the pump filter might be clogged; refer to the Care and Cleaning section for instructions on cleaning it. Ensure the drain hose isn't kinked or that the washer isn't sitting on it, and check your household plumbing for clogs, calling a plumber if necessary. Finally, make sure the drain hose isn't siphoning by ensuring there's an air gap between the hose and drain and that it's not inserted more than 7 inches into the drain pipe.
S
Shari VincentAug 7, 2025
What to do if GE PFW870 Washer has no power or is not working?
- J
  Joyce HawkinsAug 7, 2025
  If your GE Washer has no power or isn't working, first, ensure the cord is securely plugged into a working outlet. Then, check that both hot and cold water faucets are fully turned on. Also, inspect your house's circuit breakers or fuses, replacing fuses or resetting the breaker as needed, ensuring the washer has a separate outlet. If it's the first time the washer is plugged in, automatic system checks occur, which may take up to 20 seconds before you can use the washer; this is normal.
N
Natasha RamirezAug 16, 2025
Why are the clothes too wet after washing in my GE PFW870?
- A
  Anthony SullivanAug 16, 2025
  If your GE Washer leaves clothes too wet, it could be due to a few reasons. The load might be out of balance, so try redistributing the clothes and running a Rinse & Spin cycle. The pump filter may be clogged; see the Care and Cleaning section for cleaning instructions. Overloading the washer can also cause this issue; ensure the dry weight of the load is less than 16 lbs. Check that the drain hose isn't kinked or that the washer isn't sitting on it. Lastly, make sure the drain hose isn't siphoning by ensuring there's an air gap between the hose and drain and that it's not inserted more than 7 inches into the drain pipe. Also, check your household plumbing for clogs, calling a plumber if necessary.
G
Gregory DaughertyAug 20, 2025
How to stop loud noise, vibration, or shaking in my GE PFW870 Washer?
- J
  James PerezAug 21, 2025
  If your GE Washer is making loud or unusual noises, vibrating, or shaking, several factors could be responsible. The washer is designed to move slightly (about 1/4 inch) to reduce forces transmitted to the floor, which is normal. Ensure all rubber leveling legs are firmly touching the floor by pushing and pulling on the back of the washer to check its level, adjusting the legs as needed and locking them in place. An unbalanced load can also cause this; pause the unit, open the door, and manually redistribute the load. To test the machine, run a rinse and spin cycle with no load. If it runs normally, the unbalance was caused by the load. A clogged pump filter may also be the cause; refer to the Care and Cleaning section for instructions on cleaning the Pump Filter.
K
kcunninghamAug 28, 2025
Why is my GE PFW870 cycle incomplete or the timer not advancing?
- D
  Denise MaxwellAug 28, 2025
  If your GE Washer cycle is incomplete or the timer isn't advancing, it could be due to the automatic load redistribution feature, which can add up to 3 minutes to the cycle for each rebalance, possibly doing 11 to 15 rebalances. This is normal, so allow the machine to finish the wash cycle. A clogged pump filter may also be the cause; refer to the Care and Cleaning section for instructions on cleaning the Pump Filter. Additionally, a kinked or improperly connected drain hose can cause this issue, so straighten the drain hose and ensure the washer isn't sitting on it. Also, check your household plumbing for clogs, calling a plumber if necessary. Finally, ensure the drain hose isn't siphoning by ensuring there's an air gap between the hose and drain.