Why does my GE UNC15NJ-II Ice Maker make ice but also an unusual noise?
If your GE Ice Maker is making unusual noises, start by checking the panels for vibrations and ensure they are properly fitted and screws are tightened. Inspect the fan blade for any foreign objects or misalignment. Also, check for any tubes rubbing against a panel or another tube. If the drain pump is cutting in and out, inspect the valve and replace if necessary.
What to do if my GE UNC15NJ-II has a water leak?
If your GE Ice Maker has a water leak, check the drain tube for any cracks or if it has come off, and repair or reattach it as needed. Also, inspect the water inlet connection to ensure it is tight; tighten if loose.
What to do if the ice sweep is not turning in my GE UNC15NJ-II?
If your GE Ice Maker's compressor is on, the fan is on, the auger motor is on, but the ice sweep isn't turning, check the ice sweep. If it's tight to the auger, it indicates the auger isn't turning. If the gears are stripped, replace the gear reducer.
What to do if fan blade is not turning on my GE Ice Maker?
If your GE Ice Maker's compressor is on, the fan is on, but the fan blade isn't turning, check the fan blade for ease of rotation and remove any blockages. If it still doesn't turn, check the fan motor and replace it if it's not turning freely or if the motor windings are open.
How to troubleshoot no ice from my GE UNC15NJ-II?
If your GE Ice Maker isn't producing ice, start by ensuring it's properly plugged into a power supply. If it is plugged in, try pushing and releasing the ON/OFF button. Also, check the water supply and sensor, and ensure the water valve isn't restricted or shut off improperly. If you have a pump model, check for water backup or an open safety switch.
What to do if GE Ice Maker is not keeping up with ice production?
If your GE Ice Maker makes ice but less than normal, try these steps: Vacuum the condenser fins to remove any dirt. Check for and clear any blockage of airflow. Inspect the drain for restrictions and ensure proper air venting if it's a gravity drain. For pump drains, check the pump switch operation and drainage. Also, examine the door gasket and door fit to ensure they are tightly sealed.
Why GE Ice Maker compressor and fan are on, but the auger motor is not operating?
If your GE Ice Maker's compressor is on, the fan is on, but the auger motor isn't working, check the auger motor for voltage. If there's no voltage, replace the controller. If there is voltage, check the auger motor windings; if they're open, replace the auger motor.
What to check if GE UNC15NJ-II Ice Maker auger motor and fan are on, but the compressor is not drawing power?
If your GE Ice Maker's auger motor is on, the fan is on, but the compressor isn't drawing power, check the compressor start relay and the compressor windings.
Why does GE Ice Maker auger motor cut out on over amp safety?
If your GE Ice Maker's compressor is on, the fan is on, and the auger motor is cutting out due to over-amp safety, inspect the evaporator for ice and thaw it out before retrying. Also, check the top bearing and condition of the auger, and replace them if worn. You can also briefly operate the unit with the auger removed.
What to do if auger motor is on but compressor and fan motor are off on GE UNC15NJ-II Ice Maker?
If the auger motor is on, but the compressor and fan motor are off in your GE Ice Maker, try restarting the unit. Check for power to the compressor and/or fan motor. If there is no power, replace the controller.
General| Control Type | Electronic |
|---|---|
| Type | Undercounter |
| Ice Storage Capacity | 26 lb |
| Width | 14.88 inch |
| Depth | 23.63 inch |
| Installation | Built-In |
| Door Style | Solid |
| Power Supply | 115 V |
| Water Supply | Requires a water supply line |
| Weight | 98 lb |
To Next Page
