Gecko in.yj-3-ce - User Manual

To Next Page

Heater connections

(P3 & P4 Element, P5 Ground)

CO - Communication links

in.touch, in.stik, Aux keypad in.k120

P33 - Light outputs

(12 V DC, 500 mA Max.)

Main power

entry connection

Aperture Ø 2.54 cm (1'')

Neutral:

connect all Blue wires : P18, P19, P20 or P35

Ground:

connect all Green wires: P27, P28, P29 or P30

Outputs:

in.yj-3 pack has 3 relay

controlled outputs

Out 1: K6-P and Tabs P23 & P39

Out 2: K7-P

Out 3: K5-P

Direct: P25

C1 - Main keypad

connector

P1 - Heater communication cable

Bonding lugs:

connect redundant

ground cable to

heater, pumps, etc.

75 L/min (20 GPM) minimum water flow required.

This side up

Quick Start Card

in.yj-3-ce

™

European version

1- Connect all outputs & keypads

2- Connect the main power

WARNING!

in.yj.ce models must always be connected to a circuit protected by a Residual-

Current Device (RCD) having a rated operating residual-current not exceeding

30 mA. Correct wiring of the electrical service box, RCD, and pack terminal

block is essential! Check your electrical code for local regulations. Only copper

wire should be used, never aluminum.

230 V, 50 Hz (3 wires): The in.yj supports single phase input with up to 40Amp.

At first startup the keypad display

will show L 1 or LL 1.

4- Select breaker current

3- Select spa configuration (see chart next page)

Use the Up/Down key to choose the

new low level configuration number.

Press and hold the Program key

for 20 seconds until you access the

breaker setting menu.

Note: For the Color keypad series,

select Settings menu, go into Electri-

cal config and choose input current.

The values displayed by the system

correspond to the maximum

amperage capacity of the RCD.h

Specify the current rating and the number of phases of the RCD used to ensure safe and efficient current management (and no RCD trippings).

Current setting

# of phases Current setting range

1 10 to 40 A

Use the Up/Down key to select the

desired value. Then press the Program

key to confirm the selection.

Note: If the keypad does not have

the Program or Filter key, use the

Light key instead.

Press the Program key to confirm the

selection.

2 3

Note: To re-enter the Low level

selection menu, hold the Pump 1

key for 30 seconds.

Note: If the keypad does not have a

Program or Filter key, use the Light

key instead.

Note: For the Color keypad series,

select Settings menu, go into

Electrical config and choose the

appropriate Low level.

For more information, see our

website: www.geckoalliance.com

For more information, see our

website: www.geckoalliance.com

Need help?

Do you have a question about the Gecko in.yj-3-ce and is the answer not in the manual?

Summary

Connecting Outputs and Keypads

Connection Points and Wiring

Details various connection points including heater communication, light outputs, communication links, main keypad, heater connections, and grounding.

Power and Grounding Details

Specifies connections for main power entry, neutral, and ground wires, including bonding lugs.

Connect the Main Power

Power Input Requirements

Details the main power input as 230V, 50 Hz, single phase, supporting up to 40 Amp.

Select Spa Configuration

Low Level Configuration Setup

Instructions for selecting the low level configuration number using keypad buttons.

Configuration Notes and Alternatives

Provides notes for different keypad types and alternate key usage for configuration.

Select Breaker Current

Breaker Current Setting Procedure

Guide to specify RCD current rating and phases for safe current management.

Breaker Setting Notes

Notes for color keypad series and alternate key usage for setting input current.

Configuration Selection Chart

Standard Configuration Options

Presents a chart detailing various standard configurations for pumps, blower, circ. pump, ozone, filter cycles, and heater.

Glossary of Terms

Defines key terms used in the configuration selection, such as P1, P1L, 1SP, and 2SP.