To Next PageTo Next PageWhy my Genie Garage Door Opener only runs closed?
If your garage door only runs closed, first, ensure that the Sure-Lock™ is turned OFF. Check if the limits are properly set. Verify the door balance, its condition, and the door spring. Lastly, check the opening “FORCE” control.
How to fix Genie 2055 that works with wall control but not remote?
If your Genie garage door opener operates with the wall control but not the remote, here are a few things to try: * Check all remotes. * Replace the remote battery. * Program the remotes to the powerhead.
Why is my Genie Garage Door Opener running slowly?
If your Genie door opener is running slowly: * Check the operating condition of the door. The door may need professional repair or adjustment. * Verify that the opener is not installed on a one-piece door, as it is not designed for this type of door.
What to do if my Genie Garage Door Opener starts down, then stops and goes back up?
If this is a new installation, verify the door arm position. Also, check if the limits are properly set. Inspect the Safe-T-Beam® system; a flashing red LED indicates a problem. Ensure there are no obstructions or misalignment of lenses in the Safe-T-Beam® system. Check the garage door for any binding issues. If these steps don't resolve the issue, and you need to close the door, press and hold the wall control button until the door closes completely.
Why does my Genie 2055 start for no reason?
If your garage door opener starts unexpectedly, it could be due to a button stuck on the wall control or remote. Also, consider whether a remote was lost or stolen. If so, erase all remotes from the powerhead memory and program new remotes.
How to reduce noisy operation of my Genie Garage Door Opener?
Ensure all door fasteners are tight. Be sure the garage door is in good repair, properly lubricated, and balanced. Also, be sure the opener is in good repair.
What to do if my Genie 2055 starts down, then stops before it is closed, or only opens?
Check the Safe-T-Beam® wire connection at the powerhead and at the STBs. Check if the limits are properly set and adjust them if needed. Also, check CONTACT REVERSE and the garage door for binding. Finally, check the closing “FORCE” control.
How to fix a Genie 2055 Garage Door Opener that runs, but the door does not move?
Ensure the carriage is engaged with the chain/belt turnbuckle. Also, check to make sure the chain/belt is not broken or off its pulley.
Why does my Genie 2055 stop before closing?
If your Genie garage door starts to go down but stops before it fully closes, or if the door will only open, try the following: * Check the Safe-T-Beam® wire connections at the powerhead and at the STBs. * Make sure the limits are properly set, and adjust them if necessary. * Check the CONTACT REVERSE feature. * Inspect the garage door for any binding. * Check the closing “FORCE” control.
Why does my Genie 2055 Garage Door Opener remote have short range?
If your Genie garage door opener remote has a limited operating range or isn't working at all, consider these solutions: * Try relocating the remote inside your car and/or point it directly at the garage door. * Replace the remote battery. * Reposition the door opener antenna. * Identify and eliminate any potential competing signals from other devices (like radios). * Be aware that LED bulbs might interfere with the remote signal.
Details potential hazards associated with garage door operation and safety.
Provides critical safety instructions for operating garage door openers.
Highlights crucial warnings for safe and proper installation of the opener.
Details the buttons and LEDs on the powerhead for programming.
Critical warnings regarding setting the down travel limit.
Instructions on setting and understanding force control.
Table detailing powerhead LED indicators and their meanings.
Details potential hazards associated with garage door operation and safety.
Provides critical safety instructions for operating garage door openers.
Highlights crucial warnings for safe and proper installation of the opener.
Details the buttons and LEDs on the powerhead for programming.
Critical warnings regarding setting the down travel limit.
Instructions on setting and understanding force control.
Table detailing powerhead LED indicators and their meanings.
General| Model | 2055 |
|---|---|
| Horsepower | 1/2 HP |
| Frequency | 60 Hz |
| Battery Backup | No |
| Type | Chain Drive |
| Drive Type | Chain Drive |
| Lighting | 75-watt incandescent bulb (not included) |
| Voltage | 120V |
| Motor Type | AC |
| Security | Rolling code technology |
| Door Compatibility | 7 ft. door (8 ft. with extension kit) |
