To Next PageTo Next PageWhy does my Genie 2562 work from the wall control but not the remote?
If your Genie Garage Door Opener works from the wall control but not from the remote, try the following: * Check all remotes. * Replace the remote battery. * Program the remotes to the powerhead.
Why does my Genie 2562 run slowly?
If your Genie Garage Door Opener runs slowly: * Check the operating condition of the door, as it may need professional repair or adjustment. * Note that openers will run slower on one-piece doors, which is normal.
What to do if my Genie 2562 starts down, then stops and goes back up?
If your Genie Garage Door Opener starts going down and then stops and goes back up, or if there's a Safe-T-Beam system malfunction: * For new installations, verify the Door Arm position. * Also for new installations, ensure that you're only using the Safe-T-Beams that came with the opener. * Check the limit settings and adjust if needed. * See if the Safe-T-Beam red LED is flashing. * Inspect the Safe-T-Beam system for obstructions or misalignment. * Ensure the garage door isn't binding. If the opener still won't close, you can force it to close by pressing and holding the wall control button until it's fully closed. Also, check for interference from nearby Safe-T-Beam units.
What to do if Genie Garage Door Opener starts down, then stops before closing?
If your Genie Garage Door Opener starts to go down but then stops before it is completely closed, or if the door will only open, you should: * Check the Safe-T-Beam wire connections at the powerhead and STBs. * Check and adjust the limit settings if necessary. * Check the CONTACT REVERSE feature. * Inspect the garage door for any binding issues. * Check the closing “FORCE” control.
How to fix a Genie 2562 Garage Door Opener that doesn't work when the wall control is pressed?
If your Genie Garage Door Opener doesn't operate when you press the wall control, here's what you can do: * Turn Sure-Lock™ OFF. * Check the power source by plugging a lamp into the outlet used for the powerhead. If the lamp works, the power source is OK. If not, check the fuse or circuit breaker. * Check the connections at the powerhead terminals and at the wall console. * Check for reversed, broken, or cut wires. Repair or replace any damaged wires.
What to do if Genie Garage Door Opener starts up, but stops before opening completely?
If your Genie Garage Door Opener starts up but stops before it is completely open: * Check and adjust the limit settings if needed. * Ensure the door, opener, and springs are in good repair, properly lubricated, and balanced. * Check the closing/opening “FORCE” control.
Why does my Genie 2562 remote have short range?
If your Genie Garage Door Opener remote has less than 25 feet of operating range or doesn't operate at all, try these steps: * Relocate the remote inside your car and point it at the garage door. * Replace the battery. * Reposition the door opener antenna. * Eliminate possible competing signals (radio, etc.). * Consider that LED bulbs may be interfering with the remote signal.
What to do if my Genie Garage Door Opener runs, but the door doesn't move?
If your Genie Garage Door Opener runs, but the door does not move, you can: * Make sure the carriage is engaged with the chain/belt bullet or screw. * Check to make sure the chain/belt is not broken or off its pulley.
Why does my Genie Garage Door Opener only run closed?
If your Genie Garage Door Opener only runs closed: * Turn Sure-Lock™ OFF. * Check the limit settings. * Check the door balance, condition, and door spring. * Check the opening “FORCE” control.
General| Type | Chain Drive |
|---|---|
| Horsepower | 1/2 HP |
| Warranty | 5-year limited motor warranty, 1-year limited parts warranty |
| Voltage | 120V |
| Security | Rolling code technology |
| Max Door Height | 7 ft (extendable to 8 ft with extension kit) |
| Remote Controls | Two 3-button pre-programmed remote controls |
Discusses potential hazards associated with garage door openers and the importance of reading safety information.
Explains the meaning of safety alert symbols, signal words (DANGER, WARNING, CAUTION), and notes used in the manual.
Provides essential safety instructions for operating and maintaining the garage door opener safely.
