1. DESCRIPTION AND TECHNICAL SPECIFICATIONS page.7
2. DIMENSIONS page.7
3. MAXIMUM USE CURVE page.7
4. ELECTRONIC DEVICES (standard system) page.7
5. INSTALLING THE AUTOMATED SYSTEM page.8
5.1. PRELIMINARY CHECKS page.8
5.2. MASONRY FOR FOUNDATION PLATE page.8
5.3. MECHANICAL INSTALLATION page.8
5.4. INSTALLING THE RACK page.8
6. START-UP page.9
6.1. CONNECTION OF CONTROL BOARD page.9
6.2. POSITIONING THE TRAVEL-LIMIT ELEMENTS page.9
7. AUTOMATED SYSTEM TEST page.10
8. MANUAL OPERATION page.10
9. RESTORING NORMAL OPERATION MODE page.10
10. SPECIAL APPLICATIONS page.10
11. MAINTENANCE page.10
12. REPAIRS page.10
13. ACCESSORIES page.10
INDEX
DECLARATION OF INCORPORATION FOR PARTLY
COMPLETED MACHINERY
(2006/42/EC ANNEX II P.1, B)
Manufacturer and person authorised to draft the applicable technical documentation
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Hereby declares that the partly completed machinery:
Description: Gear motor for sliding gates
Model: FALCON 14 M - FALCON 14 MC - FALCON 20 M- FALCON 20
MC - FALCON 15 M - FALCON 15 MC
the following essential requirements of the Machinery Directive 2006/42/EC
(including all applicable amendments) have been applied and fulfilled:
1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.3, 1.2.5, 1.2.6, 1.3.1,
1.3.2, 1.3.4, 1.3.6, 1.3.9, 1.4.1, 1.4.2.1, 1.5.1, 1.5.2,
1.5.5, 1.5.6, 1.5.7, 1.5.8, 1.5.10, 1.5.11, 1.6.1, 1.6.4,
1.7.1, 1.7.2, 1.7.3, 1.7.4.2, 1.7.4.3
and that the relevant technical documentation has been compiled in compliance
with part B of Annex VII.
Furthermore, the following harmonised standards have been applied:
EN60335-1:2012 + A11:2014
EN60335-2-103:2015
EN 12100:2010
EN 13849-1:2015 CAT 2 PL “C”
EN 13849-2:2012
Undertakes to transmit by mail or by e-mail, in response to a reasoned request by
the national authorities, relevant information on the partly completed machinery.
It is also declared that the partly completed machinery identified above may not be com-
missioned until the final machine - into which it will be incorporated - has been declared
complaint with the provisions of the above mentioned Machine Directive 2006/42/EC.
Bologna, Italy, 04-12-2018 CEO
A. Marcellan
EU DECLARATION OF CONFORMITY
The Manufacturer
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares under his sole responsibility that the following product:
Description: Gear motor for sliding gates
Model: FALCON 14 M - FALCON 14 MC - FALCON 20 M- FALCON 20
MC - FALCON 15 M - FALCON 15 MC
Complies with the following relevant Union harmonization legislations:
2014/30/EU
2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN61000-6-2:2005
EN61000-6-3:2007 + A1:2011
Bologna, Italy, 04-12-2018 CEO
A. Marcellan
FALCON M 6 00058I0616 - Rev.1
Translation of the original instructions
ENGLISH
To Next Page
Loading...
Need help?
General
