DygiZone

GJD910 Advanced Multi-function, 4 zone, security lighting

controller and enunciator

INTRODUCTION

The DygiZone 4 zone security lighting controller works in

conjunction with GJD’s 4 Zone Expansion Unit and range

of external detectors.

PACKAGE CONTENTS

1 x DygiZone 4 zone security lighting controller

2 x xing screws

2 x wall plugs

1 x installation guide

POWERING UP THE DYGIZONE

After powering up the DygiZone controller with the battery

removed:

• Each zone’s status LEDs (red, yellow and green)

and blue zone buttons will ash

• All LCDs icons will display on the screen

When installation is completed removing the backup

battery tab will enable the clock to keep running in the

event of power loss

NOTE: Press any button to clear the display.

Alternatively, the display will clear automatically after

1 minute.

When the display clears, and if nothing is activated:

• The LCD displays the clock time (automatically

defaults to 00:00 if the battery is not connected)

• The symbol M appears on the DygiZone which is

congured as the master controller.

Note: The letter M does not appear when setting up a

DygiZone as a slave controller.

• Each zone’s status LEDs will display the zone’s

current programme state.

Note: The factory default setting is audible and

automatic for all active zones (red and green status

LEDs illuminated).

ZONE INDICATOR ICONS

For each of the 4 zones there are a set of sub-zone icons

that appear above the respective zone’s status LEDs.

Note: These icons will not be displayed until a detector

on the system has triggered.

When a detector connected to the A1, A2 or A3 input of the

Expansion Unit is triggered:

• The LCD will display the numbers 1,2 and 3 above

the respective zone number.

• A circle will appear around the number that

corresponds to the detector that has been triggered.

• The corresponding zone’s button will illuminate.

Note: The numbers 1, 2 and 3 correspond to the

Expansion unit inputs A1, A2 and A3 respectively.

Upon activation the circle will ash for 8 seconds and then

will remain visible for a time duration equal to the setting

of TIME MINS in the engineer programming. The numbers

1, 2 and 3 will also be visible for this time but will not ash.

Once this time has elapsed, all the icons will clear from the

LCD.

ZONE MODES & STATUS INDICATORS

Audible Mode: Beep or voice mode is activated and will

sound on detector activation.

Status Icon: Musical note icon for either voice

or beep more. The microphone icon is only

visible if voice mode is selected.

Status LED: Red, constantly lit.

Automatic Mode: Works in conjunction with the photocells

in the detectors. The external security lights will only be

activated if it is dark, thereby saving energy.

Status Icon: Stick gure icon

Status LED: Green, constantly lit LED

indicates mode selected.

Yellow LED illuminates when the external

lighting is activated.

Manual Override Mode: The external security light will

now remain on irrespective of detector status - useful for

barbecues or when working outside in the dark for long

periods.

Status Icon: Light bulb icon

Status LED: Yellow, lit during light activation

period.

Time Mode: External security lights will be illuminated as

per the TIME 1 or Timer 2 options.

Status Icon: Light bulb icon

Status LED: Yellow, lit during light activation

period.

Note: Zone status icons are only visible when the

respective zone button is pushed. The icons are

located in the top-centre of the LCD display.

INDIVIDUALLY SETTING ZONES

Each zone can be individually congured from the keypad

by cycling through the available modes.

The conguration process is as follows:

• Press the button for zone you would like to congure.

The zone’s status LEDs and icons will be displayed.

• Press the button again to cycle through the different

modes available until the desired mode is reached.

GJD DygiZone - Installation Manual

Other manuals for GJD DygiZone

Related product manuals