SYSTEM OPERATION
5
Please adhere to the following warnings and cautions when
installing, adjusting, altering, servicing, or operating the
furnace.
REE ER JR R E E RER
JE ER ERCE R ECE REER
.
R CE R R C
QE ER ERCE EC R E ER.
RC C R RCE CEC R CEC C
CE ER E R E C RE K E
E
C
R CE CCER R EEC R ER
RERCE R.
REE E RER E ER JR R E
E EECRC CK E RCE E CE REC
E EECRC CE R ER.
Discharge your body’s static electricity before touching
components.
Use the following precautions during furnace installation and
servicing to protect the integrated control module from damage.
By putting the furnace, the control, and the person at the same
electrostatic potential, these steps will help avoid exposing
the integrated control module to electrostatic discharge. This
procedure is applicable to both installed and non-installed
(ungrounded) furnaces.
1. Disconnect all power to the furnace. Do not touch the
integrated control module or any wire connected to the
control prior to discharging your body’s electrostatic charge
to ground.
2. Firmly touch a clean, unpainted, metal surface of the furnaces
near the control. Any tools held in a person’s hand during
grounding will be discharged.
3. Service integrated control module or connecting wiring
following the discharge process in step 2. Use caution not to
recharge your body with static electricity; (i.e., do not move or
you come in contact with an ungrounded object, repeat step
2 before touching control or wires.
4. Discharge your body to ground before removing a new control
from its container. Follow steps 1 through 3 if installing the
control on a furnace. Return any old or new controls to their
containers before touching any ungrounded object.
TO PREVENT PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO
FIRE, DO NOT INSTALL THIS FURNACE IN A MOBILE HOME, TRAILER, OR
RECREATIONAL VEHICLE.
Furnace Alone
- - - - - -
Furnace + 1 Stage Non-Communicating A/C
- - -
Furnace + 1 Stage Non-Communicating A/C
- - -
Furnace + 2 Stage Non-Communicating A/C
- - -
Furnace + 1 Stage Non-Communicating H/P
- - -
Furnace + 2 Stage Non-Communicating H/P
- - -
Furnace + Communicating A/C
- - -
Furnace + Communicating H/P
- - -
Furnace + Communicating A/C Inverter
- - -
Furnace + Communicating H/P Inverter
- - -
*All combinations assume non-communicating single stage thermostat &
AHRI matched equipment.
This furnace is primarily designed for residential home-heating
applications. It is NOT
homes, trailers or recreational vehicles. Neither is it designed
be
installed indoors (i.e., attic space, crawl space, or garage area
provided the garage area is enclosed with an operating door).
This furnace can be used in the following non-industrial
commercial applications:
In such applications, the furnace must be installed with the
following stipulations:
• It must be installed per the installation instructions provided
and per local and national codes.
• It must be installed indoors in a building constructed on site.
• It must be part of a ducted system and not used in a free air
delivery application.
• It must not be used as a “make-up” air unit.
• It must be installed as a two-pipe systems for combustion
air.
• All other warranty exclusions and restrictions apply
appropriate for use with natural or propane gas (
If using propane, a propane conversion kit is required).
optional and the furnace can be vented as a:
• Non-direct vent (single pipe) central forced air furnace in
which combustion air is taken from the installation area or
from air ducted from the outside or,
To Next Page
Loading...
