Goodway RAM-PRO-XL - User Manual

14 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

RAM-PRO-XL

VARI-SPEED REVERSING

REAM-A-MATIC TUBE CLEANER

WITH CHEMICAL DISPENSER

Operating and

Maintenance

Instructions

Read before operating.

Table of Contents

Questions and Answers

M
mckaysarahAug 10, 2025
Why is water leaking from the base of my Goodway Cleaning Equipment?
- K
  kmoonAug 10, 2025
  If you notice water leaking from the base of your Goodway Cleaning Equipment, there are several potential causes. It could be a leak in the water circuit plumbing. To address this, disconnect the power and remove the cover to inspect hoses and fittings for leaks. Another possibility is a leak at the shaft manifold seal; check the area where the driveshaft enters the shaft manifold. Finally, the water pressure might be too high, in which case you should lower the water pressure.
I
ithorntonAug 20, 2025
What to do if Goodway Cleaning Equipment runs briefly then stops and the GFCI trips?
- J
  Jacob SimpsonAug 20, 2025
  If your Goodway Cleaning Equipment runs for a short period and then stops (with the power light off) and the GFCI trips and won't reset, this indicates an electrical short to ground. If the GFCI continually trips, it is important to call Goodway, as there may be an unsafe electrical condition.
M
Meghan MartinAug 28, 2025
How to troubleshoot a Goodway RAM-PRO-XL Cleaning Equipment motor that jerks or runs erratically?
- J
  Jamie CooperAug 28, 2025
  If the motor of your Goodway Cleaning Equipment jerks or runs erratically, it could be related to the speed control. Check the speed control potentiometer by checking the resistance across the outer leads (should be approximately 5K ohms). Also, check the resistance between the middle and outer lead while rotating the speed control (should vary from 0 to 5K ohms). Another potential cause is the control board. Refer to the wiring diagram and check the trimmer pot settings.

Summary

Important Safety Instructions

Electrical Precautions

Operational Precautions

The RAM-PRO-XL Ream-A-Matic

How It Works

Explains the Ream-A-Matic's function using a rotating shaft, brush, and water flush system.

Enhanced Tubes Operation

Details how rotational speed affects feed rate for tubes with internal grooves.

Smooth-Bore Tubes Operation

Describes setting rotational speed for smooth bore tubes for efficient cleaning.

Setting the Speed Control

Instructions on adjusting rotational speed via the unit's control panel.

Forward;Reverse Foot Pedal

Explains the operation and direction control using the two-way foot pedal.

Operation

Chemical Dispenser

Roll Cage and Handle Operation

Connecting the SQC Flexible Shaft

Storage and Maintenance

Wiring Diagram

Troubleshooting Guide

Exploded View and Parts List

Goodway RAM-PRO-XL Specifications

General

Brand	Goodway
Model	RAM-PRO-XL
Category	Cleaning Equipment
Language	English

Related product manuals

Preview: Goodway REAM-A-MATIC RAM-5 GT

Goodway REAM-A-MATIC RAM-5 GT

Goodway REAM-A-MATIC RAM-5-DC

Preview: Goodway Ream-A-Matic

Goodway Ream-A-Matic

Goodway REAM-A-MATIC RAM-4

Preview: Goodway GVC-18000

Goodway GVC-18000

Preview: Goodway SOOT-A-MATIC SAM-3

Goodway SOOT-A-MATIC SAM-3

Preview: Goodway QUICK SHOT QS-300

Goodway QUICK SHOT QS-300

Preview: Goodway GDS-C40

Goodway GDS-C40

Preview: Goodway REAM-A-MATIC Series

Goodway REAM-A-MATIC Series