GRAUPNER harpoon II - Page 70

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Änderungen vorbehalten! Keine Haftung für Druckfehler! Ident-Nr. 0057999 Made in Thailand
04/2003
70
70
Parts list
Part Description Material Note
No.
1 Fuselage GRP
2 Canopy GRP
3 Clear canopy Astralon
4 Pair of wing panels GRP
5 Wing joiner tube Aluminium
6 2 fins GRP
7 Thrust vectoring pipe Stainless steel
8 2 pivot bearing discs Pertinax / Novotex For thrust vectoring pipe
9 2 bearings Machined alum. For thrust vectoring pipe
10 4 screws, M3 x 8 Steel For thrust vectoring pipe
11 3 captive nuts, M6 Steel Canopy / wing fixing
12 Nylon screw, M6 Canopy fixing
13 2 socket-head cap screws, M6 x 20 Wing fixing
14 16 self-tapping screws, 2.9 x 12 Servo-Lock fixing
15 5 Novotex horns Pertinax / Novotex Control surfaces,
speedbrake
16 2 small Novotex horns Pertinax / Novotex Rudder
17 2 strips plywood, 30 x 350 x 0.8 Turbine hatch strip
18 1 strip plywood, 30 x 350 x 0.8 Speedbrake stiffener
19 2 machined plywood parts, 3 mm Turbine hatch stiffener
20 Machined plywood part, 3 mm Rear canopy stiffener
20a Plywood part, 3 mm Front canopy stiffener
21 Machined plywood part, 5 mm Cockpit former
22 4 machined plywood parts, set Servo-Locks
23 Machined plywood part, 3 mm Bottom former
24 Machined plywood part Valve plate
25 Machined plywood part, 3 mm Turbine electronics plate
26 Plywood panel, 80 x 32 x 5 Vector servo plate
27 Machined plywood part, 3 mm Switch support
28 Steel rod, 2 Ø x 250 Turbine hatch latch
29 2 plastic sleeves, 3.2 x 2.2 Ø x 330
30 Woven glass tape
31 2 pin-hinges
32 Steel rod, 0.8 Ø x 500 Hinge alignment tool
33 10 retainer plates For cable ties
34 15 small cable ties
35 10 large cable ties
36 2 socket-head cap screws, M3 x 30 Mechanical valve fixing
37 2 self-locking nuts, M2
38 Screw, M4 x 16 ) Valve plate fixing
39 Washer, 6.4 x 4 ) to longitudinal former
40 Captive nut, M4 )
41 Servo-Lock
42 Self-tapping screws, 2.2 Ø x 6.5
43 2 pushrod connectors
44 2 self-locking nuts, M2
45 Brass tube, 2 Ø x 1.2 Ø x 100
46 Braided wire, 1 m Steerable nosewheel
47 Grubscrew, M2 Pushrod connector, 43
48 Heat-shrink sleeve Speedbrake servo
49 Steel rod, 2 Ø x 150 Shaped part, Fig. 6
50 Self-tapping screw, 2.9 x 9.5
51 Threaded rod, M3 x 1000 Aileron / Speedbrake
linkage
52 Threaded rod, M2.5 x 1000 Rudder / Vector linkage
53 Brass tube, 4 x 2.6 Ø x 1000 Reinforcement, 52