Gree GWC12ATCXB-K6DNA1B - Page 25

22
Technical Information
Service Manual
● Set temperature range from remote controller: 16~30°C(61-
86°F). Fan speed: auto,quiet,low speed, low-medium
speed,medium speed,medium-high speed, high speed.
● This mode indicator is not available for some models.
Under COOL or HEAT mode, press this button to turn to quick
COOL or quick HEAT mode. "
" icon is displayed on remote
controller. Press this button again to exit turbo function and " "
icon will disappear. If start this function, the unit will run at super-
high fan speed to cool or heat quickly so that the ambient temp.
approachs the preset temp. as soon as possible.
● Press "
" or " " button once increase or decrease
set temperature 1°C (°F). Holding " " or " " button, 2s later, set
temperature on remote controller will change quickly. On releasing
button after setting is nished, temperature indicator on indoor unit
will change accordingly.
● When setting T-ON, T-OFF or CLOCK, press " " or " "button
to adjust time. (Refer to CLOCK, TON, T-OFF buttons)
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
This button is used for setting Fan Speed in the sequence that
goes from AUTO,
, , , , to , then back to
Auto.
NOTE:
● Under AUTO speed, air conditioner will select proper fan speed
automatically according to factory default setting.
● It's low fan speed under dry mode.
● X-FAN function: Holding fan speed button for 2s in cool or dry
mode, the icon "
" is displayed and the indoor fan will continue
operation for a few minutes in order to dry the indoor unit even
though you have turned off the unit. After energization, X-FAN
OFF is defaulted. X-FAN is not available in auto, fan or heat
mode.
This function indicates that moisture on evaporator of indoor unit
will be blowed after the unit is stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit by
pressing ON/OFF button, indoor fan will continue running for a few
minutes at low speed. In this period, hold fan speed button for 2s
to stop indoor fan directly.
Having set X-FAN function off: After turning off the unit by pressing
ON/OFF button, the complete unit will be off directly.
NOTE:
● Press this button continuously more than 2s, the main unit will
swing back and forth from left to right, and then loosen the button,
the unit will stop swinging and present position of guide louver will
be kept immediately.
● Under left and right swing mode, when the status is switched
from off to
, if press this button again 2s later, status will
switch to off status directly; if press this button again within 2s,
the change of swing status will also depend on the circulation
sequence stated above.
● The function is only available for some models.
Press this button can select up & down swing angle. Fan blow
angle can be selected circularly as below:
● When selecting "
", air conditioner is blowing fan
automatically. Horizontal louver will automatically swing up &
down at maximum angle.
● When selecting "
、 、 、 、
", air conditioner
is blowing fan at xed position. Horizontal louver will stop at the
xed position.
● When selecting "
、 、
", air conditioner is blowing fan at
xed angle. Horizontal louver will send air at the xed angle.
● Hold " "button above 2s to set your required swing angle.
When reaching y our required angle, release the button.
NOTE:
● “
、 、
" may not be available. When air conditioner
receives this signal, the air conditioner will blow fan automatically.
● Press this button continuously for more than 2s, the main
unit will swing back and forth from up to down, and then loosen
the button, the unit present position of guide louver will be kept
immediately.
● Under up and down swing mode, when the status is switched
from off to , if press this button again 2s later, status will switch to
off status directly; if press this button again within 2s, the change
of swing status will also depend on the circulation sequence
stated above.
● T-ON button
"T-ON" button can set the time for timer on. After pressing this
button, "
" icon disappears and the word "ON" on remote
controller blinks. Press " " or " " button to adjust T-ON setting.
After each pressing " " or " " button, T-ON setting
will increase or decrease 1min. Hold " " or " " button, 2s later,
the time will change quickly until reaching your required time.
Press "T-ON" to conrm it. The word "ON" will stop blinking. "
" icon resumes displaying. Cancel T-ON: Unde the condition that
T-ON is started up, press "T-ON " button to cancel it.
FAN
TURBO
/
no display
position)
(stops at current
no display
(horizontal louvers stops
at current position)
T-ON T-OFF