Gree GWC12ATCXB-K6DNA1B - Page 26

23
Technical Information
Service Manual
● T-OFF button
"T-OFF" button can set the time for timer off. After pressing this
button, "
" icon disappears and the word "OFF" on remote
controller blinks. Press "
" or " " button to adjust T-OFF
setting. After each pressing "
" or " " button, T-OFF setting
will increase or decrease 1min. Hold "
" or " "button, 2s later,
the time will change quickly until reaching your required time.
Press "T-OFF" word "OFF" will stop blinking. "
" icon resumes
displaying. Cancel T-OFF. Under the condition that T-OFF is
started up, press "T-OFF" button to cancel it.
NOTE:
● Under on and off status, you can set T-OFF or T-ON
simultaneously.
● Before setting T-ON or T-OFF, please adjust the clock time.
● After starting up T-ON or T-OFF,set the constant circulating
valid.
After that,air conditioner will be turned on or turned off according
to setting time.ON/OFF button has no effect on setting.If you don’t
need this function, please use remote controller to cancel it.
● When the timer function is started up and the remote controller
is not used for a long time, the air conditioner can be turned on
or turned off by the timer function. You are suggested to put the
remote controller at the position where the indoor unit can receive
the remote signal, which can lead to more accurate timer.
Press this button to start I FEEL function and "
" will be
displayed on the remote controller. After this function is set, the
remote controller will send the detected ambient temperature
to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this
button again to cancel I FEEL function
and "
" will disappear.
● Please put the remote controller near user when this function
is set. Do not put the remote contro ller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate amb ient temperature.
When I FEEL function is turned on, the remote controller should
be put within the area where indoor unit can receive the signal
sent by the remote controller.
Press this button to set clock time. "
" icon on remote controller
will blink. Press " " or " " button within 5s to set clock time.
Each pressing of " " or " " button, clock time will increas e or
decrease 1 minute.If hold " " or " " button, 2s later, time will
change quickly. Release this button when reaching your required
time. Press "CLOCK" button to conrm the time. " " icon stops
blinking.
NOTE:
● Clock time adopts 24-hour mode.
● The interval between two operations can't exceed 5s.
Otherwise, remote controller will quit setting status.
Operation for TIMER ON/TIMER OFF is the same.
I FEEL
CLOCK
● Press this button, can select Sleep 1 ( 1), Sleep 2 ( 2),
Sleep 3 ( 3) and cancel the Sleep, circulate between these, after
electried, Sleep Cancel is defaulted.
● Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run
for one hour, the main unit setting temperature will increase 1 ,
two hours, setting temperature increased 2°C, then the unit will
run at this setting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature
will decrease 1 , two hours, setting temperature will decrease 2 ,
then the unit will run at this setting temperature.
● Sleep 2 is sleep mode 2, that is air conditioner will run according
to the presetting a group of sleep temperature curve.
● Sleep 3-the sleep curve setting under Sleep mode by DIY;
(1) Under Sleep 3 mode, press “Turbo” button for a long time,
remote controller enters into user individuation sleep setting
status, at this time, the time of remote controller will display “1hour”,
the setting temperature “88” will display the corresponding
temperature of last setting sleep curve and blink (The rst entering
will display according to the initial curve setting value of original
factory);
(2) Adjust " " and " " button, could change the corresponding
setting temperature, after adjusted, press “Turbo” button for
conrmation;
(3) At this time, 1hour will be automatically increased at the timer
position on the remote control, (that are "2hours" or "3hours" or
"8hours"), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep
curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours
temperature setting nished, sleep,curve setting nished, at this
time, the remote controller will resume the original timer display;
temperature display will resume to original setting temperature.
● Sleep3- the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire the
presetting sleep curve, enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button
directly for conrmation. Note: In the above presetting or enquiry
procedure, if continuously within 10s, there is no button pressed,
the sleep curve setting within 10s, there is no button pressed, the
sleep curve setting status will be automatically quit and resume
to display the original displaying. In the presetting or enquiry
procedure, press "ON/OFF" button, "Mode" button, "Sleep" button,
the sleep curve setting or enquiry status will quit similarly.
SLEEP
Press " WiFi " button to turn on WiFi function, " WiFi " icon will be
displayed on the remote controller; Hold " WiFi " button for 5s to
turn off WiFi function and " WiFi " icon will disappear.
Under off status, press "MODE" and " WiFi " buttons
simultaneously for 1s, WiFi module will restore factory settings.
NOTE
● The function is only available for some models.
WiFi