Gree GWH09YC-K6DNA1A - Page 22

19
Technical Information
Service Manual
2. FAN button
Press this button,
Auto, Low, Medium-low, Medium, Medium-high, High speed can be circularly selected. After powered on, Auto fan speed
is default. Under DR
Y mode, Low fan speed only can be set up.
3. MODE button
Press this button,
Auto, Cool, Dry, Fan, Heat mode can be selected circularly. Auto mode is default while power on. Under Auto mode, the
temperature will not be displayed;Under Heat mode, the initial value is 28°C( 82°F);Under other modes, the initial value is 25°
C(77°F).
4. +/- button
● Presetting temperature can be increased.
Press this button,the temperature can be set up, continuously press this button and hold for two seconds, the relative contents
can quickly
change,until unhold this button and send the order that the °C(°F) signal will be displayed all the time.The temperature adjust
ment is
unavilable under the
Auto mode, but the order can be sent by if pressing this button.Temperature of Celsius degree setting:16-30;for
Fahrenheit degree setting:61-86.
● Presetting temperature can be decreased.
Press this button, the temperature can be set up, continuously press this button and hold for two seconds, the relative content
s can quickly
change,until unhold this button and send the order that the °C(°F) signal will be displayed all the time.The temperature adjust
ment is
unavailable under the
Auto mode,but the order can be sent by if pressing this button.
5. TURBO button
Under Cool or Heat mode,press this button can turn on or turn of
f the Turbo function.After the Turbo function turned on, the signal of Turbo
will displa
y. The signal will be automatically cancelled if changing the mode or fan speed.
6. button
7KLVIXQFWLRQLVRQO\DYDLODEOHIRUVRPHPRGHOV
Press this button to set left & right swing angle cycling as below:
7. button
Press this button to set swing angle,which circularly changes as below
:
This remote controller is universal. If it receives threes kinds of following status,the swing angle will remain origial.
If guide louver is stopped when it is swinging up and down,it will remain its present position.
8. CLOCK button
Press this button, the clock can be set up,signal blink and displa
y.Within 5 seconds, the value can be adjusted by pressing + or - button,
if continuously press this button for 2 seconds above,in every 0.5 seconds, the value on ten place of Minute will be increased
1.During
After
powered on, 12:00 is defaulted to display and signal will be displayed. If there is signal be displayed that denotes
the current time
value is Clock value, otherwise is
Timer value.
9. TIMER ON/TIMER OFF button
●
Timer On setting: Signal “ON”will blink and display,signal will conceal,the numerical section will become the timer on setting status.
During 5 seconds blink,by pressing + or - button to adjust the time value of numerical section,every press of that button,the v
alue will be
increased or decreased 1 minute.Hold pressing + or - button,2 seconds late
r,it quickly change,the way of change is: During the initial 2.5
seconds,ten numbers change in the one place of minute,then the one place is constant,ten numbers change in the ten splace of m
inute at
2.5 seconds speed and carry
. During 5s blink,press the Timer button,the timer setting succeeds.The Timer On has been set up,repress the
timer button,theT
imer On will be canceled. Before setting theTimer,please adjust the Clock to the current actual time.
● One press this key to enter into TIMER OFF setup, in which case the TIMER OFF icon will blink. The method of setting is the sameas for
Note: It’s Low fan speed
under Dry mode.
(only for cooling and heating unit.
As for cooling only unit, it won’t
have any action when it receives
the signal of heating operation.)
Medium fanLow fan High fan
Medium-low fan Medium-high fan
ATUO
AUTO COOL DRY FAN HEAT
OFF
OFF