What to do if Gree GWH12YC-K6DNA1A has refrigerant leakage?
If the refrigerant in your Gree Air Conditioner is leaking or insufficient, check for leaks, fix them, vacuumize the system, and then add the required amount of refrigerant.
How to fix Gree Air Conditioner compressor malfunction?
If your Gree Air Conditioner's compressor is malfunctioning, replace the compressor.
What to do if Gree GWH12YC-K6DNA1A Air Conditioner fan capacitor is damaged?
If the fan capacitor in your Gree Air Conditioner has an open circuit or is damaged, replace it with a fan capacitor of the same type and specification.
How to fix Gree GWH12YC-K6DNA1A Air Conditioner outdoor fan motor damage?
If the outdoor fan motor of your Gree Air Conditioner is damaged, replace the fan motor.
Why Gree GWH12YC-K6DNA1A Air Conditioner fan rotation speed becomes low?
If the fan rotation speed of your Gree Air Conditioner becomes low, the capacitor might be damaged. Replace the capacitor.
What to do if Gree Air Conditioner power voltage is too low?
If the power voltage is too low for your Gree Air Conditioner, check the cause, improve the power supply condition, and consider adding a stabilized voltage power supply.
Why does the Gree GWH12YC-K6DNA1A Air Conditioner breaker trip after a few minutes?
If the breaker trips a few minutes after turning on your Gree Air Conditioner, it could be due to a malfunction in the circuit or a part of the air conditioner. Measure the insulation resistance or systematically eliminate the malfunction. If the breaker itself is faulty, replace it.
What to do if Gree Air Conditioner does not react after it is powered?
If your Gree Air Conditioner isn't responding after you power it on, check these potential causes: * Ensure the power plug is properly plugged in and has a firm connection. * If the controller fuse is burnt out, replace it. * Check the transformer connection for looseness or bad contact; fasten the wiring and measure the transformer's output voltage. If the voltage is incorrect, replace the transformer.
What to do if the Gree Air Conditioner remote controller does not receive signals?
If your Gree Air Conditioner's remote controller isn't sending signals, first press the manual switch button AUTO. If there's no response, check using the methods described earlier. If it runs normally after pressing the button, verify that the installation position and the connection wire of the reception head are correct. Also, check for receiver issues like looseness or poor connection and ensure the installation position and connection wire of the reception head are correctly placed. If the connections are correct, the receiver might be broken, consider replacing the receiver or the remote controller.
General| Cooling Capacity | 12000 BTU/h |
|---|---|
| Heating Capacity | 13000 BTU/h |
| Energy Efficiency Ratio (EER) | 3.21 |
| Seasonal Energy Efficiency Ratio (SEER) | 6.1 |
| Power Supply | 220-240V, 50Hz |
| Refrigerant | R32 |
| Weight (Indoor Unit) | 10 kg |
| Type | Split Air Conditioner |
Overview of the air conditioner's features and purpose.
Detailed technical parameters including capacity, power, and dimensions.
Visual representation of the indoor and outdoor unit dimensions.
Schematic illustrating the refrigerant flow and components.
Wiring diagrams and PCB layouts for electrical connections.
Explanation of the unit's operational modes, functions, and controls.
Essential safety precautions and guidelines for installation and maintenance.
Comprehensive guide covering unit installation steps and requirements.
Procedures for upkeep, troubleshooting, and error code interpretation.
Illustrated breakdown of unit components with part numbers.
Step-by-step instructions for safely disassembling unit components.
Conversion table for temperature units between Celsius and Fahrenheit.
Guidelines on connection pipe length and refrigerant charging.
Correct technique for expanding refrigerant pipe ends to prevent leaks.
Table correlating temperature sensor resistance with ambient temperature.
To Next Page