Gree PULAR Series

32
Technical Information
Service Manual
● Set temperature range from remote controller: 16~30
đ
(61-
●
This mode indicator is not available for some models.
86
đ
). Fan speed: auto,quiet,low speed, low-medium
speed,medium speed,medium-high speed, high speed.
Press "▲" or " ▼ " button once increase or decrease
●
●
button to adjust time. (Refer to CLOCK,
TON, T-OFF buttons)
When setting T-ON, T-OFF or CLOCK, press "▲" or " ▼ "
set temperature 1
đ
(°F). Holding "▲" or " ▼ " button, 2s later,
set
temperature on remote controller will change quickly. On
on indoor unit will change accordingl
y.
Press
this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
Under
COOL or HEAT mode, press this button to turn to quick
COO
L or quick HEAT mode. " " icon is displayed on remote
controlle
r. Press this button again to exit turbo function and
"
" icon will disappear. If start this function, the unit will
ru
n at super-high fan speed to cool or heat quickly so that
th
e ambient temp.approachs the preset temp. as soon as
possible.
●
speed automatically according to factory default setting.
It's low fan speed under dry mode.
●
●
T
his button is used for setting Fan Speed in the sequence
that goes from
AUTO, , , , , to , then
back to
Auto.
Notice:
Under AUTO speed, air conditioner will select proper fan
X-FAN function: Holding fan speed button for 2s in cool
●
Having set X-FAN function on: After turning off the unit by
or
dry mode, the icon " " is displayed and the indoor fan
will
continue operation for a few minutes in order to dry the
indoo
r unit even though you have turned off the unit. After
energization,
X-FAN OFF is defaulted. X-FAN is not available
in auto, fan or heat mode.
This
function indicates that moisture on evaporator of indoor
unit will be blowed after the unit is stopped to avoid mould.
Notice:
● Press this button continuously more than 2s, the main unit
pressing
ON/OFF button, indoor fan will continue running for
a
few minutes at low speed. In this period, hold fan speed
button for 2s to stop indoor fan directl
y.
Having
set X-FAN function off: After turning off the unit by
pressing ON/OFF button, the complete unit will be of
f directly.
●Under left and right swing mode, when the status is
will swing back and forth from left to right, and then l
oosen
the button, the unit will stop swinging and present position of
guide louver will be kept immediately.
switched from off to , if press this button again 2s later
,
●The function is only available for some models.
●
status will switch to off status directly; if press this b
utton
again within 2s, the change of swing status will also depend
on the circulation sequence stated above.
Press this button can select up & down swing angle. Fan blow
angle can be selected circularly as below:
When selecting " ", air conditioner is blowing fan
●
automatically. Horizontal louver will automatically swing up
&
down at maximum angle.
When selecting "
、 、 、 、
", air conditioner
● When selecting "
、 、
", air conditioner is blowing
●
angle.
When reaching y our required angle, release the button.
Notice:
●
Hold " "button above 2s to set your required swing angle.
“
、 、
" may not be available. When air conditioner
● Press this button continuously for more than 2s, the main
receives this signal, the air conditioner will blow fan
automatically.
●
unit will swing back and forth from up to down, and the
n
loosen the button, the unit present position of guide louver w
ill
be kept immediately.
Under up and down swing mode, when the status is
●T-ON button
switched from off to , if press this button again 2s later, status
will switch to off status directly; if press this button again
within 2s, the change of swing status will also depend on
the
circulation sequence stated above.
FAN
TURBO
/
no display
position)
(stops at current
"T-ON" button can set the time for timer on. After pressing this
button, " " icon disappears and the word "ON" on r
emote
controller blinks. Press "▲" or " ▼ " button to adjust T-ON
setting. After each pressing "▲" or " ▼ " button, T-ON setting
will increase or decrease 1min. Hold "▲" or " ▼ " button, 2
s
later, the time will change quickly until reaching your r
equired
time. Press "T-ON" to confirm it. The word "ON" will stop
no display
(horizontal louvers stops
at current position)
T-ON T-OFF