What to do if my GreenWorks Pro 7400707AU Lawn Mower fails to start after cleaning?
If your GreenWorks Pro Lawn Mower fails to start after cleaning, it might be due to improper cleaning, where water enters the battery compartment or the key switch fails, so clean it according to the instructions. If the vehicle is accidentally exposed to rain, put the vehicle in a dry place for 12 hours or dry it before use.
What to do if my GreenWorks Pro 7400707AU Lawn Mower doesn't move when I press the accelerator?
If your GreenWorks Pro Lawn Mower doesn't move when you press the accelerator, it could be due to several reasons. First, ensure that at least one Greenworks battery pack is correctly inserted into the battery compartment and that it has sufficient power. Also, check that the park brake is fully disengaged, allowing the wheels to rotate freely. Confirm that someone is sitting on the seat, or that the seat switch is properly connected. Make sure the PTO switch is in its original position when the machine is powered on. Finally, if the drive battery compartment is in sleep mode, turn the key to the OFF position and restart the machine after 5 seconds.
Why does my GreenWorks Pro 7400707AU Lawn Mower blade stop running during mowing?
The blade of your GreenWorks Pro Lawn Mower might stop running during mowing for several reasons. The blade motor could be overheated, so power off the machine for 5 minutes to allow it to cool down. The deck might be full of grass and garbage, so clean the deck to ensure normal blade rotation. The blade motor could be overloaded, so push down the PTO switch and restart the machine, also raise the deck height or reduce the drive speed to protect the blade. If the battery pack temperature is too high or the battery is undervoltage, turn the key to the OFF position, and restart the machine 5 seconds later. Also, the blade might have hit a foreign object, causing it to stop suddenly for protection.
What to do if my GreenWorks Pro 7400707AU is vibrating too much?
Excessive vibration in your GreenWorks Pro Lawn Mower can stem from a few issues. The blade might be loose, so grind the blade according to the manual. A bent blade can also cause vibration, so replace it, wearing protective equipment. An uneven deck can be a culprit, so adjust the cutting deck to ensure the left and right deck heights are even. Also, the deck might be loose, so tighten the fixing bolts. If the blade is cutting too much grass, raise the cutting deck and avoid cutting intensive grass.
What to do if my GreenWorks Pro 7400707AU Lawn Mower cuts grass unevenly?
Uneven cutting with your GreenWorks Pro Lawn Mower can be due to a few reasons. The blade might be dull, so grind the blade according to the manual. A bent blade can also cause this issue, so replace the bent blade, wearing protective equipment. Finally, an uneven deck can lead to uneven cuts, so adjust the cutting deck to ensure the left and right deck height are even.
What to do if my GreenWorks Pro 7400707AU Lawn Mower has a sudden breakdown during driving?
If your GreenWorks Pro Lawn Mower experiences a sudden breakdown while driving, the battery may be out of power, so make sure at least one Greenworks designed battery pack is inserted in the battery compartment and that it has power. You can also try restarting the machine to check if it works normally.
What to do if there is grass or debris on the ground after mowing with my GreenWorks Pro 7400707AU?
If you notice grass or debris on the ground after mowing with your GreenWorks Pro Lawn Mower, it could be due to several factors. If the grass is too dense and high, raise the cutting deck. If the grass height exceeds 6 inches, cut the area repeatedly and avoid cutting intensive grass. Ensure the grass isn't too wet before mowing. Also, reduce your driving speed and turn the blade speed to high position.
Why does my GreenWorks Pro Lawn Mower cut the grass abnormally?
Abnormal grass cutting with your GreenWorks Pro Lawn Mower can occur if the grass is too wet, so wait until the grass gets drier. Also, if the grass amount you set is too much, raise the deck height, and avoid cutting intensive grass.
What to do if the actual cut height doesn't match the set height on my GreenWorks Pro Lawn Mower?
If the actual cut height on your GreenWorks Pro Lawn Mower doesn't match the set height, the bolt of the deck might be loose, so adjust the cutting deck bolt to ensure the deck is not loose, and balance the deck level after each adjustment. Alternatively, the deck might be severely worn or damaged, requiring replacement with a new cutting deck.
Why is the cutting endurance time short on my GreenWorks Pro 7400707AU Lawn Mower?
If you're experiencing short cutting endurance time with your GreenWorks Pro Lawn Mower, it may be due to heavy grass. Raise the cutting deck and reduce the blade speed to extend the running time.
General| Brand | GreenWorks Pro |
|---|---|
| Model | 7400707AU |
| Category | Lawn Mower |
| Language | English |
To Next Page