To Next PageTo Next Page
Need help?Do you have a question about the Guardian Fall Protection 01500 and is the answer not in the manual?
Rope Grabs support a MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications.
Rope Grabs may be used in Restraint applications to prevent workers from reaching leading edges.
Account for safety factor, deceleration distance, user height, lanyard length, and harness stretch.
Minimize swing fall hazards by working as close to in-line with anchor point as possible.
Examples of correct and incorrect connector usage with Rope Grab to prevent roll-out.
Materials used include galvanized steel, stainless steel, nylon, and polyester.
Ensure VLL compliance, compatible rope diameter, and eliminate fall hazards.
Steps to attach Rope Grab to VLL, ensuring correct orientation and secure locking.
Inspect for corrosion, deformation, pits, rough surfaces, sharp edges, cracking, rust, etc.
Competent Person inspection required, recorded in log, and on equipment label.
Do not alter equipment or misuse. Assess workplace conditions, select equipment by Competent Person.
Systems must be supervised by Competent Person and designed compliantly with regulations.
Maximum allowable free fall distance for lanyards and SRLs must not exceed limits.
Specifies compatible rope diameter (5/8") and breaking strength (6000 LBS).
Manufacturer's instructions must be read and understood prior to use.
Notes automatic functioning for dorsal attachment only.
The Guardian Fall Protection Rope Grab is a crucial component in personal fall arrest systems (PFAS) and restraint applications, designed to enhance worker safety in environments with fall hazards. This instruction manual serves as a comprehensive guide for the safe and effective use of the Rope Grab, emphasizing the importance of understanding its functionalities, limitations, and maintenance requirements. It is intended to be an integral part of an employee training program, ensuring that all users are well-versed in its operation and the associated safety protocols.
The primary function of the Rope Grab is to provide a secure and reliable connection within a fall protection system, specifically designed for use with compatible vertical lifelines (VLLs). In a personal fall arrest system, the Rope Grab acts as a mobile anchor point that travels along the VLL, allowing the worker freedom of movement while simultaneously providing continuous fall protection. Should a fall occur, the Rope Grab is engineered to engage the lifeline, arresting the fall and minimizing the impact forces on the worker. This mechanism is critical for preventing workers from striking the ground or any obstructions below.
For restraint applications, the Rope Grab's function shifts to preventing workers from reaching a fall hazard's leading edge. In this mode, it limits the worker's range of motion, ensuring they remain within a safe zone where a fall cannot occur. This is particularly useful on sloped surfaces where the risk of sliding or falling is present. The Rope Grab's design allows for automatic functioning, ensuring it moves smoothly along the lifeline as the worker changes position, providing constant protection without requiring manual adjustment during normal operation.
The Rope Grab is designed to be compatible with 5/8" diameter ropes, ensuring a secure grip and reliable performance. Its construction from galvanized steel or stainless steel, combined with nylon and polyester components, ensures durability and resistance to various environmental factors. The device incorporates a positioning arrow, which guides proper installation by indicating the correct orientation towards the VLL anchorage, thereby ensuring optimal functionality.
The Guardian Fall Protection Rope Grab offers several usage features that contribute to its effectiveness and user-friendliness. One key feature is its compatibility with a vertical lifeline, allowing for vertical mobility while maintaining continuous fall protection. The device is designed to be fully closed and locked to the VLL once installed, providing a secure attachment that prevents accidental disengagement.
Depending on the specific part number, some Rope Grabs include an extension lanyard or a shock-absorbing extension lanyard. These extensions provide additional flexibility in connecting to the worker's harness D-ring, while still adhering to the maximum distance requirement between the Rope Grab and the D-ring to ensure proper fall arrest performance. For specific models, such as part #01506, the Rope Grab can transition between "trailing" and "positioning" functionalities. In the trailing mode, it follows the worker's movement along the VLL. When used as a positioning device, lifting the D-ring allows for repositioning along the VLL, offering versatility for different work scenarios.
A critical usage feature is the emphasis on eliminating or minimizing swing fall hazards. The manual strongly advises working as close as possible to directly in line with the anchor point to prevent swing falls, which can significantly increase the risk of serious injury. The Rope Grab's design facilitates this by allowing the worker to maintain a position directly below the anchor.
The Rope Grab is designed for a worker weight capacity range of 130-310 lbs, including all clothing, tools, and equipment, making it suitable for a broad spectrum of users. It is imperative that all connections made with the Rope Grab are compatible and free from the risk of roll-out, where interference could unintentionally open a hook gate. All connector gates must be self-closing and self-locking, capable of withstanding minimum loads of 3,600 lbs, ensuring the integrity of the fall protection system.
Effective maintenance is paramount to ensuring the safety and longevity of the Guardian Fall Protection Rope Grab. The manual outlines clear maintenance features and guidelines to help users preserve the equipment's integrity.
A fundamental maintenance feature is the requirement for immediate removal from service if the Rope Grab fails inspection in any way. This proactive approach prevents the use of compromised equipment, thereby safeguarding worker safety. Users are instructed to contact Guardian for return or repair inquiries if deficiencies are found.
Cleaning is a vital aspect of maintenance. The Rope Grab should be cleaned before and after each use to remove all dirt, corrosives, and contaminants. If plain water is insufficient, mild soap and water can be used, followed by rinsing and wiping dry. The explicit instruction to NEVER clean the Rope Grab with corrosive substances highlights the importance of preserving the material integrity of the device.
Proper storage is another key maintenance feature. When not in use, the equipment should be stored in an environment where it is protected from heat, light, excessive moisture, chemicals, and other degrading elements. This helps prevent premature wear and tear, ensuring the Rope Grab remains in optimal condition for future use.
Regular inspection is a critical maintenance feature. Prior to EACH use, the user must inspect the Rope Grab for any deficiencies, including corrosion, deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, and missing or illegible labels. If any defects or damage are found, or if the equipment has been exposed to fall arrest forces, it must be IMMEDIATELY removed from service.
Beyond daily user inspections, a formal inspection by a Competent Person (other than the user) is required at least every 12 months. This Competent Person inspection must be meticulously recorded in an inspection log within the instruction manual and on the equipment inspection grid label. The Competent Person's initials and the date of inspection must be recorded, providing a clear audit trail of the equipment's maintenance history. This rigorous inspection schedule ensures that any potential issues are identified and addressed promptly, maintaining the highest standards of safety for the Rope Grab throughout its indefinite product lifetime, provided it continues to pass all inspection requirements.
General| Product Type | Fall Protection Harness |
|---|---|
| Model Number | 01500 |
| Brand | Guardian Fall Protection |
| D-Ring Locations | Back |
| Weight Capacity | 310 lbs |
| Material | Polyester |
| Standards | ANSI |
| Compliance | OSHA 1926 Subpart M |
