GW Instek PEL-2000 Series - Page 64

268 pages

To Next Page

To Previous Page

PEL-2000 Series User Manual

Load

Current

Voltage

High

Low

CC Mode: Static:Go/NoGo

Current

NoGoNoGo

GO is specified as between the Low and High

Go/NoGo limits. NoGo is specified as outside the

Go/NoGo limits.

All manuals and user guides at all-guides.com

Main Page

Table of Contents3
Safety Instructions5
Getting Started11
Main Features12
Series Overview13
Package Contents and Accessories15
Measurement Overview16
Front Panel Overview17
Display Overview - Mainframe22
Rear Panel Overview25
Front Panel Overview - Load Module28
LED Display Overview - Load Module32
Installation35
Load Module Installation35
GPIB Installation38
Rack Mount Installation39
Channel Number40
Power up & Self Test41
Load Connections43
Precautions and Procedures43
Remote (Sense) Connection48
Single Load Connections50
Parallel Load Connections52
Frame Link Connection54
Channel Control Connection56
Go/Nogo Connection59
Operating Description60
Operating Mode Description61
Constant Current Mode61
Constant Resistance Mode65
Constant Voltage Mode68
Run Program71
Sequence74
Parallel Dynamic Loading78
Configurations Description79
Protection Modes79
Operating Configurations81
Channel Control85
Interface and File System89
Interface89
File System89
File Format94
Tutorials96
Local Loads97
Single Channel Load99
Programming101
Sequences103
Frame Link104
Channel Control106
General Configuration Options108
Operation109
Local Mode Operation112
Selecting a Channel113
Selecting Static/Dynamic114
Turning on the Load115
Shorting116
Display Output View117
Editing CC /CR/CV A/B Value118
Mainframe Basic Operation119
Help Menu120
Channel Selection121
Select CC Mode122
Select CC Range123
Select CC Dynamic Mode123
Editing CC Dynamic Parameters124
Select CC Static Mode126
Editing CC Static Parameters126
Set to CR Mode128
Select CR Range128
Select CR Dynamic Mode129
Editing CR Dynamic Parameters130
Select CR Static Mode132
Editing CR Static Parameters132
Select CV Mode134
Editing CV Parameters135
Select CV Response Speed137
Creating a Program Sequence138
Program Chains143
Running a Program145
Edit Sequence151
Create Sequence Loop153
Channel Duration Time Settings155
Run Sequence157
Channel Configuration160
Accessing the Configuration Menu161
Setting (OCP/OVP/OPP/UVP)162
Protection Clear165
Setting the CC Voltage Range165
Adjusting the von Voltage and Latch167
Configuring the Short Key168
Configuring Channel Control170
Configuring the Independent Setting171
Configuring the Load Delay Time173
Configuring Step Resolution175
Go/Nogo177
Mainframe Configuration180
Accessing System Information181
Accessing the Load Menu182
Configuring the Date and Time183
Adjusting the Speaker184
Adjusting the Display Settings185
Adjusting the Frame Control187
Adjusting the Knob Control Type188
Configuring Alarm Sound190
Configuring Go/Nogo Alarm Sound191
Adjusting Slave Knob Settings192
View Language Settings194
Interface Configuration (Settings)195
Configuring RS232 Connection196
Configuring the GPIB Address198
Configuring USB Remote Connection199
Save / Recall201
Saving/Recalling Channels202
Saving/Recalling Preset Memory204
Saving/Recalling Setup Memory206
Setting the Default USB Path/File208
Saving Setups to USB Memory213
Saving/Recalling Memory Data to USB216216
Saving/Recalling Presets to USB220
Saving/Recalling Sequences to USB224
Quick Preset Recall/Save228
Recall Setup Memory (Frame Link)229
Recall Preset Memory (Frame Link)230
Recall Factory Defaults231
Interface232
Interface Configuration233
Configure RS-232C Interface233
Configure GPIB Interface234
Configure Channel Control Interface235
Configure Frame Link Interface236
Configure Go/Nogo Interface239
USB Interface Connection240
Faq241
Appendix242
Fuse Replacement242
Battery Replacement243
Firmware Update244
Calibration245
Range Chart246
Default Settings251
Specifications253
Dimensions261
EC Declaration of Conformity263
Index265

GW Instek PEL-2000 Series - Page 64

Table of Contents

Other manuals for GW Instek PEL-2000 Series