Why AWS System is ON, but rear tires do not follow behind the front tires in Hagie DTS10?
If the AWS System is ON in your Hagie Paint Sprayer, but the rear tires do not follow behind the front tires, note that this is left up to the operator’s discretion.
What to do if Hagie DTS10 Paint Sprayer engine overheats?
If the engine of your Hagie Paint Sprayer overheats, you can try the following: * Reduce the load on the engine. * Remove any foreign material and clean all components. * Replace the radiator cap. * Check the fan speed. * Replace the thermostat. * Refill the coolant to the proper level.
How to troubleshoot Hagie DTS10 Paint Sprayer engine that will not start?
If your Hagie Paint Sprayer's engine won't start, consider these steps: * Fill the fuel tank. * Replace the fuel filter(s). * Disengage the E-Stop Switch. * Check the starter and battery. * Check or replace the fuse.
What to do if Hagie DTS10 Paint Sprayer solution pump will not prime?
If the solution pump on your Hagie Paint Sprayer won't prime, make sure the solution tanks are not empty. Also, inspect the vent line or vent check valve for any blockage or kinking. Inspect and tighten all fittings in the suction line, and open the solution tank valve to allow air to leave the system.
What to do if AWS System inoperable, machine will only move at slow speed in Hagie DTS10?
If the AWS System is inoperable and the Hagie Paint Sprayer will only move at slow speed, move the Hydrostatic Drive Control Handle to NEUTRAL, wait for the “FAULT” drive state to disappear on the Machine Display, and restart the machine. Note that in Road mode, the rear tires are locked until the machine is put into Field mode.
Why does the engine knock on my Hagie DTS10 Paint Sprayer?
If the engine of your Hagie Paint Sprayer knocks, try the following: * Add oil to the full mark. * Allow a proper warm-up period, referring to the engine manufacturer’s operation manual.
Why solution pump not producing adequate pressure in Hagie Paint Sprayer?
If the solution pump on your Hagie Paint Sprayer isn't producing adequate pressure: * Remove the screen, clean it thoroughly, and tighten the strainer cap to prevent air leaks. * Inspect and tighten all fittings on the suction line. * Ensure the Main Tank Valve is completely open. * Check for any obstruction at the inlet end of the hose that could be causing high vacuum on the hose.
How to fix erratic reading on pressure gauge of Hagie Paint Sprayer?
If you're getting an erratic reading on the pressure gauge of your Hagie Paint Sprayer: * Remove the gauge, clean the orifice, and reinstall it. * Replace the gauge. * Inspect and tighten all fittings in the suction line. * Check the solution strainer.
How to fix noisy hydrostatic system in Hagie DTS10 Paint Sprayer?
If you have a noisy hydrostatic system in your Hagie Paint Sprayer, allow an adequate warm-up period, increase the engine speed, and fill the hydraulic reservoir to the proper level with approved oil.
What to do if Hagie DTS10 will not move in either direction?
If your Hagie Paint Sprayer machine will not move in either direction, set the engine at operating RPM, fill the hydraulic reservoir to the proper level with approved oil, and replace the pressure filter.
General safety rules and precautions for operating the machine safely.
Safe practices for handling agricultural chemicals to protect operator health and the environment.
Proper use and function of the emergency stop switch for immediate engine shutdown.
Procedures and safety precautions for starting the machine's engine.
Warnings and guidelines for the Final Tier 4 engine aftertreatment system and DEF.
Overview of the hydrostatic drive system, its components, and operation.
Enabling and operating the All-Wheel Steer system for improved maneuverability.
Adjusting the machine's tread width using hydraulic controls for field conditions.
Location, handling, and charging procedures for the machine's batteries.
General| Brand | Hagie |
|---|---|
| Model | DTS10 |
| Category | Paint Sprayer |
| Language | English |
To Next Page
