Haier E Series User Manual

24
+6824L/H(A
POWER/SOFT
Outdoor Unit
Parts and Functions
Indoor Unit
Remote controller
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:
Cooling only unit do not have disp
l
ays and functions related with heating
Used to select CODE A or B with a press,
A or B will be displayed on LCD.
Please select A without special explanation.
1.CODE
When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.
2.RESET
Used to select TIMER ON, TIMER OFF,TIMER ON-OFF.
4. TIMER button
Used to set correct time.
5. CLOCK button
Used to select sleep mode.
6. SLEEP button
7. MODE button
AUTO COOL DRY FAN
HEAT
Used to set clock and timer setting.
8. HOUR button
Used for unit start and stop.
10. ON/OFF button
11. TIMER ON display
12. FAN SPEED display
LOW HIMED AUTO
13. LOCK display
14. SWING UP/DOWN display
15. SLEEP display
16. HEALTH display
Used to select your desired temperature.
17. Operation mode display
19.POWER/SOFT display
20. Left/right air flow display
Remote controller: to display theTEMP. setting.
21. TEMP display
22. TIMER OFF display
23. CLOCK display
24. TEMP button
Used to select fan speed: LOW,MED, HI, AUTO.
25. FAN button
Used to set the health airflow mode.
26. HEALTH AIRFLOW button
27. SWING UP/DOWN button
Used to select up or down air sending direction.
28. SWING LEFT/RIGHT button
Used to select left/right air flow.
30
Used to confirm timer and clock settings.
31.
SET button
Used to lock buttons and LCD display. If pressed, the
other buttons will be disabled and the lock condition
display appears. Press it once again, lock will be
canceled and lock condition display disappears.
LOCK
18.Signal sending display
3.LIGHT button
Control the lightening and extinguishing of
the indoor LED display board.
14
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
1
2
3
4
Remove the battery cover;
Load the batteries as illustrated.2 R-03
batteries, resetting key (cylinder);
Be sure that the loading is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or room,
the receiver is apt to be disturbed in receivingthe signals, so the
Note:
Full display or unclear display during operation indicates the
If the remote controller can't run normally during operation, please
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
Hint:
Loading of the battery / Clock set
remove the batteries and reload several minutes later.
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time.
will change quickly. After time setting is
stop flashing while clock starts working.
Each press will increase or decrease
1
2
3
POWER/SOFT
FRESH
28
19
Used to set healthy function.
9. HEALTH button
32.
POWER/SOFT button
Used to set power/soft function.
Operation mode
AUTO FANCOOL DRY
Remote controller
Display board
HEAT
6
5
2
1
4
3
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
6
4
2
1
5
3
5
2
1
5
3
6
8
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust up and down air flow
Don't adjust it manually)
(adjust left and right air flow)
Vertical blade
4
Display board
8
4
2
3
1
6
5
7 8
(inside)
Anion generator
7
7
4
batteries have been used up.Please change batteries.
AUTO COOL DRY FAN HEAT
19
28
30
9.
SWING button
Used for unit start and stop.
10
. ON/OFF button
11. TIMER ON display
12. FAN SPEED display
LOW HIMED AUTO
13. LOCK display
14. SWING UP/DOWN display
15. SLEEP display
16. HEALTH display
Used to select your desired temperature.
17. Operation mode display
19. POWER/SOFT display
20. Left/right air flow display
Remote controller: to display the TEMP. setting.
21. TEMP display
22. TIMER OFF display
23. CLOCK display
24. TEMP button
Used to select fan speed: LOW,MED, HI, AUTO.
25. FAN button
Used to set the health airflow mode.
26. HEALTH AIRFLOW button
27. SLEEP button
Used to select up or down air sending direction.
Used to confirm timer and clock settings.
28. SET button
29. POWER/SOFT button
Use to set power/soft function.
Used to select CODE A or B with a press,A or B
will be displayed on LCD.
Please select A without special explanation.
1.CODE
When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.
2.RESET
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.
4. TIMER button
Used to set correct time.
5. CLOCK button
6. HEALTH button
7. MODE button
Used to set clock and timer setting.
8. HOUR button
Used to lock buttons and LCD display. If pressed, the
other buttons will be disabled and the lock condition
display appears. Press it once again, lock will be
cancelled and lock condition display disappears.
30. LOCK
Used to set healthy operation.
Used to select sleep mode.
POWER/SOFT
18.Signal sending display
3.LIGHT button
Control the lightening and extinguishing of
the indoor LED display board.
Operation mode
AUTO FANCOOL DRY
Remote controller
Display board
HEAT
If the unit which you purchased has SWING LEFT/RIGHT function,follow it.If not,please ignore.
Signal receiver hole
COOL display
HEAT display
HEALTH display
Dry display
4
2
3
1
6
7
5
(If the unit which you purchased
has healthy function,follow it.
TIMER OFF display
TIMER ON display,SLEEP display
If not,please ignore.)
Ambient temp.display
(When receiving the remote control signal,
display the set temperature and in the rest
this room temperature is only for reference.)
time the room temperature is displayed and
AUTO display
8
Clock set
1min. If the button is kept pressed,time
confirmed,press SET,"AM "and "PM"
29 FRESH button
Use to set fresh air function.
(This function is unavailable on this models.)
Все каталоги и инструкции здесь: http://splitoff.ru/tehn-doc.html

Haier E Series Specifications

General

Brand	Haier
Model	E Series
Category	Air Conditioner
Language	English