+., 167=?6 @A4?A9<8 A6@A ?B< +7=? 4:: 264A >B;> ;=56:@,
+/, 36@A ?B<
[vp ujg vpku eqpukpvqvtny hqs cdqvu MJ okpvugtH cpf ejgem ujg hqnnqxkpiI
\veukqp rsgttvsg cu ejgem lqkpu qh tgswkeg wcnwg hqs ict rkrgI
Qktejcsig rsgttvsg cu ejgem lqkpu qp ujg eqorsgttqs fktejcsig rkrgI
]gorgscuvsg fkhhgsgpeg dguxggp sguvsp cks cpf tvrrny cks hqs kpfqqs vpkuI
0- 36@A ?B<
PN^]VYXD ]UV\ ^XV] `VWW OR \]N[]RQ VX\]NX]Wb `V]UY^] EYXE YZR[N]VYX `URX RWRP][VP ZY`R[
V\ \^ZZWVRQIOR \^[R ]Y RaRP^]R EYSSE YZR[N]VYX ORSY[R RWRP][VP ZY`R[ V\ QV\PYXXRP]RQ
SY[ \R[_VPVXTI
]jkt vpku jct c hvpeukqp qh cvuqocuke sgtucsu tytugo chugs sgeqwgskpi rqxgs tuqrrcigI
Pqphkso xjgujgs ujg rqxgs tqvseg dsgcmgs Fockp txkuejG qh ujg vpku jct dggp uvspgf qp hqs qwgs KL jqvst uq
gpgsikzg ujg escpmectg jgcugs kp cfwcpeg qh qrgscukqpI
Oil trap is required no mater the outdoor unit is upper or lower than indoor unit, only when
Trap dimensions:
Setting method: install one oil trap for every 10 meters at the gas pipe.
Note: the drop between the oil trops should be 10m.
L
R
R
Gas pipe diameter Min. R (mm) L (mm)
φ15.88
40 80
φ19.05
40 80
φ25.4
40 80
φ31.8
60 90
φ38.1
60 100
the piping
drop is more than 10m.
Oil trap setting requirement:
WARNING!
INTERCONNECTING WIRES MUST BE WIRED ACCORDING TO FIG.1,FIG.2,
FIG.3 INCORRECT
WIRING MAY CAUSE EQUIPMENT DAMAGE.
(3) Wiring procedure
1) Remove set screws on the side before taking off the front panel toward the direction shown
in figure.
2) Connect wires to the terminal block correctly and fix the wires with a wire clamp equipped
3) Route the wires in a proper way and penetrate the wires through the opening for electric
nearby the terminal
block.
wiring on the side
panel.
NMTDO PRNNJV?
8Lq18=52955S1:5Gp
L678
V4F
OPQ
GAR297BE58 GAR297BH58 GAR297BG58 GAR297GH58
GBER297BE58 GBER297BG58 GBER297GI58
GCR297BE584G GCR2:5GQ584G
GCR297BH584G GCR297GI584G
Qe HdZeeh Rd_j
V4F
V4F
Qe HdZeeh Rd_j
T A O AO FO
J L89 :
V4F
OPQL
V4F
NMTDO PRNNJV?
8Lq18=52955S1:5Gp
GAR297GE58 GBER297GE58 GCR297GE584G
GCR297BG584G
Installation