What to do if my Haier Washer won't start?
If your Haier Washer isn't starting, there are several things to check: * Make sure the programme has been selected and started. * Ensure the door is properly closed. * Verify that the machine has been switched on. * Check the power supply. * Deactivate the child lock if it is activated.
What to do if my Haier HW80-B14876 shows error E4?
If your Haier Washer displays error code E4, it indicates that the water level was not reached after 12 minutes. Ensure that the tap is fully opened and the water pressure is normal. Also, check the drain hose installation, as a self-syphoning drain hose can cause this error.
How to stop my Haier HW80-B14876 Washer from vibrating so much during spinning?
Excessive vibration during spinning can occur in your Haier Washer due to several reasons. Ensure that all transportation bolts have been removed from the machine. The appliance should be on solid, level ground. An incorrect machine load can also cause strong vibrations, so check the load weight and balance.
Why does my Haier Washer stop mid-cycle?
If your Haier Washer stops before completing the wash cycle, it could be due to a water or electric failure. Check both the power and water supply.
What does error E2 mean on my Haier HW80-B14876 Washer?
Error E2 on your Haier Washer indicates a lock error. Ensure that the door is shut properly.
Why is there no water in my Haier Washer?
If your Haier Washer isn't filling with water, several issues could be the cause. First, ensure the water tap is open. Also, check the inlet hose for any kinks that might be blocking the water flow. Low water pressure (less than 0.03 MPa) can also prevent the washer from filling. Confirm that the door is properly closed and that there are no water supply failures.
What to do if my Haier Washer has a drainage failure?
If your Haier Washer is experiencing a drainage failure, first check if the drain hose is blocked and unblock it. Also, ensure that the drain hose end is not higher than 100 cm above the floor level, making sure that the drain hose is properly installed.
Why is my Haier HW80-B14876 Washer draining immediately?
If your Haier Washer is draining immediately, it might be because the height of the drain hose is below 80 cm, so make sure that drain hose is properly installed. Another reason could be that the drain hose end is reaching into the water. In this case, make sure the drain hose is not in water.
Why is the spinning cycle failing on my Haier HW80-B14876 Washer?
If the spinning cycle is failing on your Haier Washer, it could be due to an unbalance of laundry. Check the machine load and laundry, then run the spinning programme again.
How to reduce excessive foam in my Haier HW80-B14876?
Excessive foam in your Haier Washer can be due to using an inappropriate detergent, so check detergent recommendations. It can also be caused by using too much detergent, so reduce the amount of detergent you're using.
General| Door hinge | Left |
|---|---|
| Control type | Rotary, Touch |
| Loading type | Front-load |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | - |
| Appliance placement | Freestanding |
| Drum capacity | 8 kg |
| Cycle time (max) | 235 min |
| Wi-Fi controlled | No |
| Delay start (max) | 24 h |
| Residual moisture | 53 % |
| Spin-drying class | B |
| Maximum spin speed | 1330 RPM |
| Noise level (spin) | 66 dB |
| Noise level (wash) | 53 dB |
| Number of washing programs | 16 |
| AC input voltage | 220 - 240 V |
| Power consumption (off) | 0.42 W |
| Power consumption (left-on) | 0.52 W |
| Energy consumption washing per cycle | 117 kWh |
| Package weight | 78000 g |
| Annual water consumption washing | 9500 L |
| Annual energy consumption washing | 0.54 kWh |
Weight and Dimensions| Depth | 460 mm |
|---|---|
| Width | 595 mm |
| Height | 850 mm |
| Weight | 72000 g |
Explains symbols and provides environmental disposal instructions.
Critical safety actions before the first use of the appliance.
Essential safety precautions for regular operation.
Safety guidelines for cleaning and maintenance procedures.
Safety instructions for correct installation.
Defines the appliance's purpose and restrictions for safe usage.
Visual identification of the washing machine's parts.
Lists all items provided with the washing machine.
Explains the function of all buttons and displays.
Details the purpose of each compartment in the detergent drawer.
Interpretation of symbols and messages on the appliance display.
How to select programs and use basic buttons.
Describes operations of Extra Rinse, Delay, i-time, etc.
Provides notes on factory settings and liquid detergent use with delay.
Guides on using i-time, Steam, Speed, Temp, and Child Lock.
Details available programs, their settings, and fabric types.
Presents consumption data for various wash cycles.
Explains the automatic load detection system.
Instructions for proper installation of water and electrical connections.
Guidance on sorting, preparing, and loading clothes into the machine.
Interprets care symbols and advises on detergent selection and use.
Guidelines on how to properly load laundry into the drum.
Advises on choosing and using detergents for different programs.
Procedures for switching on, selecting programs, and starting cycles.
How to add specific options and settings to a wash program.
Procedures for pausing, cancelling, and completing wash programs.
Steps after washing, including door lock, standby mode, and buzzer settings.
Advice on efficient use of energy, water, and detergent for environmental benefit.
Step-by-step guide to cleaning the detergent dispenser.
How to clean the appliance body and the internal drum.
Instructions for cleaning the water inlet valve filter to prevent blockages.
Recommendations for storing the machine and maintaining cleanliness.
Detailed steps for cleaning the pump filter, including safety warnings.
Completes the pump filter cleaning process with final checks.
Explains the meaning of various codes displayed by the appliance.
Solutions for problems like drainage errors and water filling issues.
Troubleshooting for problems related to sensors, motor, leaks, and load balance.
Solutions for issues that do not trigger specific error codes.
Procedures for managing excessive foam and power interruptions.
Steps for removing packaging and disposing of materials.
Instructions on removing all transportation bolts and securing parts.
Optional step for reducing operational noise.
How to adjust feet for stability and ensure the machine is level.
Guidance on keeping transport parts safe for future use.
Detailed instructions for connecting the drain hose to various outlets.
Instructions for connecting the water inlet hose and power plug safely.
Details energy class, consumption, spin speeds, and program times.
Physical measurements, weight, and compliance with EC directives.
Steps to resolve issues before calling for assistance.
Information on how to contact customer service and a list of service locations.
To Next Page