Why won't my Haier HW80-B14939S8 start?
Your Haier Washer might not start because the program hasn't been initiated yet, the door isn't properly closed, the machine hasn't been switched on, there's a power failure, or the child lock is activated. Ensure the program is correctly set and started, the door is securely closed, the machine is switched on, the power supply is working, and the child lock is deactivated.
How to stop my Haier HW80-B14939S8 from vibrating so much during spinning?
Excessive vibration during spinning could be due to transportation bolts not being removed, the appliance not having a solid position, or an incorrect machine load. Remove all transportation bolts, ensure the washer is on solid, level ground, and check that the load weight and balance are correct.
What to do if my Haier HW80-B14939S8 is not getting water?
If your Haier Washer isn't getting water, check the water tap to ensure it's open. Also, inspect the inlet hose for any kinks, verify that the water pressure is at least 0.03 MPa, make sure the door is properly closed and ensure a stable water supply.
How to fix the Unb error on my Haier Washer?
The 'Unb' error indicates an unbalanced load. To resolve this, check and balance the laundry load in the drum and reduce the load size if necessary.
Why is my Haier Washer showing a drainage failure?
A drainage failure can occur if the drain hose is blocked or if the drain hose end is higher than 100 cm above the floor level. Unblock the drain hose and ensure it is properly installed.
What does CLR FLTR mean on my Haier Washer?
The 'CLR FLTR' error indicates a drainage error, meaning water is not fully drained within 6 minutes. Check the drain hose installation.
Why is my Haier HW80-B14939S8 Washer constantly draining?
Your Haier Washer might be constantly draining if the height of the drain hose is below 80 cm or if the drain hose end is reaching into water. Make sure that the drain hose is properly installed and is not in water.
What to do if my Haier HW80-B14939S8 stops mid-cycle?
If your Haier Washer stops before completing the wash cycle, check both the power and water supply to ensure there are no interruptions.
Why is my Haier Washer not cleaning clothes properly?
If your Haier Washer isn't cleaning clothes properly, the selected program might not match the degree of pollution, the detergent quantity might be insufficient, the maximum load might have been exceeded, or the laundry might be unevenly distributed in the drum. Try selecting another program, use the appropriate amount of detergent according to the degree of pollution and manufacturer specifications, reduce the load size, and ensure the laundry is loosely distributed.
Why is there excessive foam in my Haier HW80-B14939S8 detergent drawer?
Excessive foam in the detergent drawer can occur if the detergent used is not appropriate or if too much detergent is being used. Check detergent recommendations and reduce the amount of detergent used.
Safety precautions to take before operating the appliance for the first time.
Guidelines for safe and proper daily operation and supervision of the appliance.
Lists and describes various wash programmes with parameters like load, temperature, and spin speed.
Step-by-step guide to switching on, selecting programmes, and starting wash cycles.
Instructions on starting, interrupting, cancelling, and finishing wash programmes.
Instructions for cleaning the detergent drawer, machine exterior, water inlet filter, and drum.
Guidance on long-term storage and cleaning the pump filter.
Provides solutions for problems indicated by specific display codes and errors.
Offers solutions for common operational issues not indicated by display codes.
Details actions to take during and after a power failure, including door unlocking.
Covers unpacking, installing noise pads, and removing transportation bolts.
General| Type | Front Load |
|---|---|
| Capacity | 8 kg |
| Spin Speed | 1400 RPM |
| Energy Rating | A+++ |
| Color | White |
| Energy Efficiency Class | A+++ |
| Programs | 15 |
| Delay Start | Yes |
| Child Lock | Yes |
| Inverter Motor | Yes |
To Next Page