Haier HWD90-BP14636 User Manual (English)

Questions and Answers:

W
Whitney PughAug 20, 2025
Why is my Haier Washer/Dryer not filling with water?
- J
  Jessica RiveraAug 20, 2025
  Your Haier Washer/Dryer might not be filling with water due to several reasons. First, check if the water tap is open and working. Also, inspect the inlet hose for any kinks that might be blocking the water flow. The inlet hose filter could also be blocked, so try unblocking it. Low water pressure (less than 0.03 MPa) can also be the cause, so verify the water pressure. Ensure that the door is properly closed and that there is no water supply failure.
W
Wayne WallaceAug 22, 2025
What to do if my Haier Washer/Dryer fails to operate?
- D
  Diana EstesAug 22, 2025
  If your Haier Washer/Dryer isn't operating, start by ensuring the programme has been correctly selected and started. Check that the door is fully closed. Make sure the machine is switched on and that there is no power failure by checking the power supply. Finally, verify whether the child lock is activated and, if so, deactivate it.
J
James SullivanAug 25, 2025
Why is my Haier HWD90-BP14636 draining while filling?
- C
  Christine OwenAug 25, 2025
  If your Haier Washer/Dryer is draining while filling, it could be because the drain hose is not installed correctly. Ensure that the height of the drain hose is at least 80 cm. Also, make sure the end of the drain hose is not submerged in water.
B
Billy WatsonAug 26, 2025
Why is my Haier HWD90-BP14636 Washer/Dryer vibrating so strongly while spinning?
- P
  Philip ChaseAug 27, 2025
  Strong vibrations during spinning in your Haier Washer/Dryer can occur if the transportation bolts haven't been removed. Also, ensure the appliance is on solid, level ground. An incorrect machine load can also cause strong vibrations, so check the load weight and balance.
K
Kim PenningtonAug 28, 2025
What to do if my Haier Washer/Dryer operation stops before completing wash cycle?
- D
  Dennis PalmerAug 28, 2025
  If your Haier Washer/Dryer stops before completing the wash cycle, check both the power and water supply to ensure there are no failures.
L
Laura ElliottAug 29, 2025
How to fix drainage failure in my Haier HWD90-BP14636 Washer/Dryer?
- R
  reedbarbaraAug 30, 2025
  To fix a drainage failure in your Haier Washer/Dryer, start by unblocking the drain hose. If that doesn't work, clean the pump filter. Also, ensure that the drain hose end is not higher than 100 cm above the floor level.
A
Allison StewartAug 31, 2025
Why is my Haier HWD90-BP14636 Washer/Dryer spinning failing?
- M
  Maria MooreAug 31, 2025
  Spinning may fail in your Haier Washer/Dryer due to an unbalance of laundry. To resolve this, check the machine load and laundry distribution, then run a spinning programme again.
S
Stephanie AndrewsSep 2, 2025
What to do if my Haier Washer/Dryer operation stops for a period of time?
- S
  stephensjasmineSep 2, 2025
  If your Haier Washer/Dryer stops for a period of time, consider any error codes displayed. This issue could also be due to the load pattern, so try reducing or adjusting the load. If the programme performs a soaking cycle, you may want to cancel the programme and restart it.
R
Regina MaySep 4, 2025
Why does my Haier HWD90-BP14636 have excessive foam?
- J
  Jocelyn MillerSep 4, 2025
  Excessive foam in your Haier Washer/Dryer may be due to using an inappropriate detergent. Check detergent recommendations and reduce the amount of detergent used.
W
William RangelSep 6, 2025
Why is my Haier Washer/Dryer showing error code E1?
- J
  Joanna CampbellSep 6, 2025
  The E1 error code on your Haier Washer/Dryer indicates a drainage error, meaning water is not fully drained within 6 minutes. Check the drain hose installation.

Haier HWD90-BP14636 Specifications

General

Type	Washer/Dryer Combo
Washing Capacity	9 kg
Drying Capacity	6 kg
Spin Speed	1400 rpm
Dimensions (H x W x D)	85 x 60 x 60 cm
Color	White
Noise Level (Washing)	56 dB
Programs	16
Delay Start	Yes
Child Lock	Yes
Display Type	LED