How to fix current detecting circuit abnormal of compressor module in Haier MRV 5-RC AB182MRERA Heat Pump?
If the current detecting circuit of the compressor module is abnormal in your Haier Heat Pump, replace the inverter control board with abnormal current detection loop.
What to do if four-way valve reversing failure in Haier Heat Pump?
In case of a four-way valve reversing failure in your Haier Heat Pump, the suggested solution is to have it correctly replaced by after-sales service on site and ensure the refrigerant is sufficient.
How to fix outdoor compressor discharging temperature (Td1, Td2) too high failure in Haier Heat Pump?
If the outdoor compressor discharging temperature (Td1, Td2) is too high in your Haier Heat Pump, the suggested solution is to have the discharging temperature sensor replaced by after-sales personnel on site.
What to do for fan motor module hardware over current in Haier Heat Pump?
If the fan motor module in your Haier Heat Pump experiences a hardware over current issue, the solution is to replace the fan motor.
What to do if radiator temp. sensor of compressor module is abnormal in Haier Heat Pump?
If the radiator temperature sensor of the compressor module is abnormal in your Haier Heat Pump, replace the variable frequency board.
How to resolve AT24C04 EEPROM communication failure in Haier Heat Pump?
To resolve AT24C04 EEPROM communication failure, AT24C04 EEPROM data check failure, or IM EEPROM data or communication failure in your Haier Heat Pump, replace EE.
How to fix emergency stop function switch failure in Haier Heat Pump?
If the emergency stop function switch fails in your Haier Heat Pump, short circuit the CN18.
What to do if incorrect settings of quantity, address or capacity for outdoor unit in Haier MRV 5-RC AB182MRERA?
If there are incorrect settings of quantity, address, or capacity for the outdoor unit of your Haier Heat Pump, the suggested solution is to research and lock the outdoor unit.
What to do if discharging temperature sensor Td1 and Td2 failure in Haier MRV 5-RC AB182MRERA?
If the discharging temperature sensors Td1 and Td2 fail in your Haier Heat Pump, the solution is to have them correctly replaced by after-sales personnel on site.
What to do if outdoor unit compressor discharging temperature (Td1, Td2) too low failure in Haier Heat Pump?
If the outdoor unit compressor discharging temperature (Td1, Td2) is too low in your Haier Heat Pump, the suggested solution is to have the discharging temperature sensor replaced by after-sales personnel on site.
Provides detailed technical specifications for various outdoor unit models.
Provides essential safety guidelines and instructions for installing the outdoor unit.
Details critical safety precautions to prevent accidents during installation.
Covers general installation checks and unit combination guidelines.
Outlines the step-by-step procedures for installing the system components.
Explains the method and cautions for connecting refrigerant pipes.
Details electrical wiring requirements, including safety and connection standards.
Lists the specifications for the VP4-450B valve box.
Covers installation procedures and safety precautions for the valve box.
Details critical warnings, attention points, and prohibitions for valve box installation.
Shows the layout of the outdoor PCB and details dip switch settings.
Provides a photo and dip switch settings for the one-by-four valve box PCB.
Details compressor operations including cycle start, number changes, and delays.
Lists failure codes specific to the outdoor unit.
Details failure codes, their descriptions, and remarks for diagnosis.
Troubleshooting steps for defrosting temperature sensor (Tdef) failures.
Troubleshooting steps for ambient temperature sensor (Tao) failures.
Troubleshooting steps for suction temperature sensor (Ts) failures.
Troubleshooting steps for discharging temperature sensor (Td1, Td2) failures.
Troubleshooting steps for high pressure sensor (Pd) failures.
Troubleshooting steps for low pressure sensor (Ps) failures.
Troubleshooting for high pressure switch (HPS1, HPS2) failures.
Troubleshooting for compressor ratio too high protection.
Troubleshooting steps for communication failures between outdoor units.
Troubleshooting for communication failures with INV1/INV2 module boards.
Troubleshooting for communication failures with fan motor module boards.
Troubleshooting for communication failures with wireless modules.
Troubleshooting for over current protection of LEVa1,2 and LEVb,c.
Troubleshooting for open circuit faults in LEVa1,2 and LEVb,c.
To Next Page
General